CCI

Overview

Applications

Electrical

Mechanical

Typical Antenna Patterns

Product Information

Software/Firmware

Parts & Accessories

Standards & Compliance

Certifications

Overview

Applications

Electrical

Mechanical

Typical Antenna Patterns

Product Information

Software/Firmware

Parts & Accessories

Standards & Compliance

Certifications

CCI Portal Login

News

Support

Solutions

Products

Services

Resources

Support

CCI Portal Login

CCI

News

Support

Solutions

Products

Services

Resources

Support

CCI Portal Login

CCI Customer Portal

CCI

News

Support

Multi-Port Antennas

In the Americas

Sales


+1 (201) 342-3338 phone
+1 (201)-342-3339 fax

89 Leuning Street
South Hackensack, NJ 07606
USA

Customer Service


+1 (201) 342-3338 phone
+1 (201)-342-3339 fax

89 Leuning Street
South Hackensack, NJ 07606
USA

Technical Support


+1 (201) 342-3338 phone
+1 (201)-342-3339 fax

89 Leuning Street
South Hackensack, NJ 07606
USA

Datasheet

OctoPort Multi-Band Antenna

OPA45R-BU5A

				Five foot (1.4 m) multiband, eight port antenna with a 45° azimuth beamwidth covering 698-798, 824-896 MHz and 1695-2400 MHz frequencies Four wide high band ports covering 1695-2400 MHz and four frequency specific low band ports covering 698-798 MHz and 824-896 MHz (over a distributed diplexer) in a single antenna Full Spectrum Compliance for WCS and AWS-3 frequencies and upcoming Band 14 Operations LTE Optimized FBR and SPR performance, providing for an efficient use of valuable radio capacity LTE Optimized Boresight and Sector XPD and USL performance, essential for LTE Performance Exceeds minimum PIM performance requirements Equipped with new 4.3-10 connector, which is 40% smaller than traditional 7/16 DIN connector Equipped with 3 field replaceable, integrated AISG 2.0 compliant Remote Electrical Tilt (RET) Controllers (Type 1 External)

Overview

The CCI OctoPort multiband array is an eight port antenna, with four wide high band ports covering 1695-2400 MHz and four frequency specific low band ports covering 698-798 MHz and 824-896 MHz. The antenna provides the capability to deploy 4×4 Multiple-input Multiple-output (MIMO) in the high band and 2x2 Multiple-input Multiple-output across each of the paired low band ports.

The CCI OctoPort allows independent tilt control between the low band ports and high band ports, in a three RET Controller (Type 1 External) configuration. The 1^st RET is dedicated for the 700 MHz Low Band ports and the 2^nd RET is dedicated for the 850 MHz Low Band ports. The 3^rd RET is dedicated for the High Band ports. With the use of a single RET in the High Band, equal tilt is achieved across all four High Band ports, which ensures optimal 4x4 MIMO performance.

CCI antennas are designed and produced to ISO 9001 certification standards for reliability and quality in our state-of-the-art manufacturing facilities.

Applications

4×4 MIMO for the high band and 2×2 MIMO for each the low band ports
Ready for Network Standardization on 4.3-10 DIN connectors
With CCI’s multiband antennas, wireless providers can connect multiple platforms to a single antenna, reducing tower load, lease expense, deployment time and installation costs

Electrical

Ports	2 × Low Band Ports for 698-798 MHz	2 × Low Band Ports for 824-896 MHz
Frequency Range	698-798 MHz	824-896 MHz
Gain¹	14.7 dBi	15.6 dBi
Gain (Average)²	14.3 dBi	14.8 dBi
Azimuth Beamwidth (-3dB)	52°	47°
Elevation Beamwidth (-3dB)	17.0°	14.8°
Electrical Downtilt	2° to 16°	2° to 16°
Elevation Sidelobes (1st Upper)	<-18 dB	<-18 dB
Front-to-Back Ratio @180°	> 30 dB	> 30 dB
Front-to-Back Ratio ±20°	> 30 dB	> 30 dB
Cross-Polar Discrimination at Peak	> 25 dB	> 25 dB
Cross-Polar Discrimination at 3 dB²	23.6 dB	21.2 dB
Cross-Polar Port-to-Port Isolation	> 25 dB	> 25 dB
Voltage Standing Wave Ratio (VSWR)	< 1.5:1	< 1.5:1
Passive Intermodulation (2×20W)	≤ -150 dBc	≤ -150 dBc
Input Power Continuous Wave (CW)	500 watts	500 watts
Polarization	Dual Linear 45°	Dual Linear 45°
Input Impedance	50 ohms	50 ohms
Lightning Protection	DC Ground	DC Ground
¹Peak gain across sub-bands. ²Electrical specifications follow document "Recommendation on Base Station Antenna Standards" (BASTA) V9.6.

Ports	4 × High Band Ports for 1695-2400 MHz
Frequency Range	1695-1880 MHz	1850-1990 MHz	1920-2180 MHz	2300-2400 MHz
Gain¹	18.4 dBi	19.2 dBi	19.6 dBi	19.7 dBi
Gain (Average)²	17.8 dBi	18.6 dBi	18.9 dBi	18.9 dBi
Azimuth Beamwidth (-3dB)	44°	43°	42°	42°
Elevation Beamwidth (-3dB)	6.7°	6.1°	5.7°	4.9°
Electrical Downtilt	2° to 10°	2° to 10°	2° to 10°	2° to 10°
Elevation Sidelobes (1st Upper)	<-17 dB	<-17 dB	<-17 dB	<-16 dB
Front-to-Back Ratio @180°	> 30 dB	> 30 dB	> 30 dB	> 30 dB
Front-to-Back Ratio ±20°	> 28 dB	> 30 dB	> 30 dB	> 30 dB
Cross-Polar Discrimination at Peak	> 20 dB	> 20 dB	> 20 dB	> 20 dB
Cross-Polar Discrimination at 3 dB²	15.7 dB	16.5 dB	17.2 dB	18.4 dB
Cross-Polar Port-to-Port Isolation	> 25 dB	> 25 dB	> 25 dB	> 25 dB
Voltage Standing Wave Ratio (VSWR)	< 1.5:1	< 1.5:1	< 1.5:1	< 1.5:1
Passive Intermodulation (2×20W)	≤ -150 dBc	≤ -150 dBc	≤ -150 dBc	≤ -150 dBc
Input Power Continuous Wave (CW)	300 watts	300 watts	300 watts	300 watts
Polarization	Dual Linear 45°	Dual Linear 45°	Dual Linear 45°	Dual Linear 45°
Input Impedance	50 ohms	50 ohms	50 ohms	50 ohms
Lightning Protection	DC Ground	DC Ground	DC Ground	DC Ground
¹Peak gain across sub-bands. ²Electrical specifications follow document "Recommendation on Base Station Antenna Standards" (BASTA) V9.6.

Mechanical

Dimensions (L×W×D)	55.4×15.4×8.2 in (1408×391×209 mm)
Survival Wind Speed	> 150 mph (> 241 kph)
Front Wind Load	189 lbs (843 N) @ 100 mph (161 kph)
Side Wind Load	113 lbs (501 N) @ 100 mph (161 kph)
Equivalent Flat Plate Area	7.4 ft² (0.7 m²)
Weight *	45.7 lbs (20.8 kg)
RET Weight	5.0 lbs (2.3 kg)
Connector	8 × 4.3-10 female
Mounting Pole	2 to 5 in (5 to 12 cm)

* Weight excludes mounting and RET

Bottom View	OPA45R-BU5A


Connection Spacing Diagram	OPA45R-BU5A

RET to Element Configuration	OPA45R-BU5AA Element and RET configuation

Typical Antenna Patterns

For detailed information on additional antenna patterns, contact customer support at


	710 MHz Azimuth with Elevation 9°	840 MHz Azimuth with Elevation 9°


	1740 MHz Azimuth with Elevation 6°	1970 MHz Azimuth with Elevation 6°


	2130 MHz Azimuth with Elevation 6°	2400 MHz Azimuth with Elevation 6°

MBK-02		MBK-02 Mounting Kit
BSA-RET200		Type 1 External Remote Electrical Tilt System (RET)
BSA-RET400		Type 17 External Remote Electrical Tilt System (RET)
HPA-CBK-AG-RRU		OctoPort antenna with 3 RET to RRU AISG cable kit
HPA-CBK-RA-AG-RRU		OctoPort antenna with 3 RET to RRU AISG right angle cable kit
SCU-AISG-P		Portable AISG 2.0 Site Control Unit

Product Information

	Datasheet
	OPA45R-BU5AA Connector Spacing Diagram
	OPA45R-BU5AA Antenna/RET Config Diagram
	MBK-02 Installation Guide

	Interactive Pattern Viewer
	CCI Interactive Pattern Viewer Instructions

Antenna Pattern

OPA45RBU5A: Text/Planet Format - Default Azimuth

Configuration File

	RET Antenna configuration file update procedure

For Firmware select RET Actuator link below.

BSA-RET200 SA-DC0301
Configuration File	Version
OPA45-BU5A-HB01.BIN	01
OPA45-BU5A-HU01.BIN	01

BSA-RET200 SA-DC0401E
Configuration File	Version
OPA45-BU5A-YB01.BIN	01
OPA45-BU5A-YU01.BIN	01

Parts & Accessories

OPA45R-BU5AA-K	Five foot (1.4 m) OctoPort antenna with 45° azimuth beamwidth, 4.3-10 female connectors, 3 factory installed BSA-RET200 RET actuators (Type 1 external) and MBK-02 mounting bracket
OPA45R-BU5AB-K	Five foot (1.4 m) OctoPort antenna with 45° azimuth beamwidth, 4.3-10 female connectors, 3 factory installed BSA-RET400 RET actuators (Type 17 internal) and MBK-02 mounting bracket
MBK-02	Mounting bracket kit (top and bottom) with 0° to 10° mechanical tilt adjustment
BSA-RET200	Type 1 Remote electrical tilt actuator
BSA-RET400	Type 17 Remote electrical tilt actuator
HPA-CBK-AG-RRU	OctoPort antenna with 3 RET to RRU AISG cable kit
HPA-CBK-RA-AG-RRU	OctoPort antenna with 3 RET to RRU AISG right angle cable kit

Standards & Compliance

Safety	EN 60950-1, UL 60950-1
Emission	EN 55022
Immunity	EN 55024
Environmental	IEC 60068-2-1, IEC 60068-2-2, IEC 60068-2-5, IEC 60068-2-6, IEC-60068-2-11, IEC 60068-2-14, IEC 60068-2-18, IEC 60068-2-27, IEC 60068-2-29, IEC 60068-02-30, IEC 60068-2-52, IEC 60068-2-64, GR-63-CORE 4.3.1, EN 60529, IP 24

Certifications

Antenna Interface Standards Group (AISG), Federal Communication Commission (FCC) Part 15 Class B, CE, CSA US, ISO 9001

	Interactive Pattern Viewer
	CCI Interactive Pattern Viewer Instructions

		PRODUCTS

	Amplifiers
	Antennas
	Co-Siting & Antenna Sharing
	DAS & Small Cell Products
	Fiberoptics
	Filters & Combiners
	PIM Analyzers

		ANTENNAS

	Antenna Accessories
	Bi-Sector™
	iDAS
	Multi-Sector/Special Events
	Single Sector Multiport
	Small Cell/oDAS
	Specialty

		FREQUENCY BAND

		HEIGHT

	2 ft. (458 - 761 mm)
	3 ft. (762 - 1066 mm)
	4 ft. (1067 - 1371 mm)
	5 ft. (1372 - 1676 mm)
	6 ft. (1677 - 1981 mm)
	8 ft. (2287 - 2590 mm)
	9 ft. (2591 - 2896 mm)

		HORIZONTAL BEAMWIDTH

	30° to 40°
	40° to 50°
	50° to 70°

		NUMBER OF PORTS

	2
	4
	6
	8
	10
	12
	>12

		LOW BAND PORTS

	2
	4
	6

		HIGH BAND PORTS

	2
	4
	6
	8
	24

89 Leuning Street

South Hackensack, NJ 07606

+1 (201) 342-3338

+1 (201) 342-3339 fax

	604-806 MHz
	698-798 MHz
	698-896 MHz
	698-960 MHz
	790-960 MHz
	824-896 MHz
	1695-1880 MHz
	1695-2180 MHz
	1695-2360 MHz
	1695-2690 MHz
	1850-1995 MHz
	2300-2400 MHz
	2300-2690 MHz
	2496-2690 MHz
	3300-3800 MHz
	1427-1518 MHz
	1427-2200 MHz
	1427-2690 MHz

FILTER BY SELECTION