Specialty Antennas

CCI Portal Login

CCI Customer Portal

CCI Register

In the Americas
   
 
 
 
Sales  
 
 
+1 (201) 342-3338 phone  
+1 (201)-342-3339 fax  
 
89 Leuning Street  
South Hackensack, NJ 07606  
USA  
 
Customer Service  
 
 
+1 (201) 342-3338 phone  
+1 (201)-342-3339 fax  
 
89 Leuning Street  
South Hackensack, NJ 07606  
USA  
 
Technical Support  
 
 
+1 (201) 342-3338 phone  
+1 (201)-342-3339 fax  
 
89 Leuning Street  
South Hackensack, NJ 07606  
USA  
 
 
      Three-Beam Special Events Antenna MBA3R-K4A
                
       
       
         
  PI MBA3RK4AA FRONT ISO  
  • Four foot (1.3 m) tall, single band, six port mutlibeam array. Containing three Independent LTE Optimized Beams covering 694-960 MHz frequencies
  • This multibeam array contains three Multibeams, each with Independent AISG RET control. Each Independent LTE Optimized Beam has an electrical downtilt range of 4°-16°, an Industry First for this type of Multibeam Array.
  • Six Low Band Dual-Pol +45°/-45°ports (two ports per beam) covering 694-960 MHz in a single antenna
  • Full Spectrum Compliance for 694-960 MHz Frequencies and upcoming Band 14 Operations
  • LTE Optimized Beams for improved LTE data throughput by minimizing beam crossover, providing for an efficient use of valuable radio capacity and frequency spectrum
  • LTE Optimized FBR, USLS and Co-Pol Beam Isolation Performance. Essential for today’s LTE Data Driven Networks
  • Exceeds minimum PIM performance requirements

Overview

 

This CCI Three-Beam Antenna contains Three Independent LTE Optimized Beams and each LTE Optimized Beam has an Independent AISG RET control. This is an Industry First, for this type of Multibeam Array. Independent RET control for each beam will allow operators tremendous flexibility in the optimization and management of their high speed data cellular networks. This Three-Beam Antenna is intended for use at data hotspots and other congested locals, where social media and the ability to share photos and videos and other high demand applications require high capacity and high data rates. This Three-Beam antenna enables maximum spectrum re-use by sectorization, greatly increasing network capacity. Our LTE Optimized Beam Design approach provides fast roll off between beams, minimizing interference between sectors thus increasing the carrier to interference plus noise (CINR) ratio and lowering soft handover losses in LTE networks. Such an approach enhances data transfer rates within LTE network sectors and addresses “hotspots” in mobile wireless operator networks.


The single panel design of the CCI Three-Beam Special Event Antenna offers the opportunity to reduce antenna count and directly replaces multiple narrow beam antennas. The antenna minimizes the need for optimization as each beam is spaced optimally for maximum throughput thus providing significant CAPEX and OPEX cost savings.
CCI antennas are designed and produced to ISO 9001:2008 certification standards for reliability and quality in our state-of-the-art manufacturing facilities.

Applications

 
  • Upgrade of data-throughput or capacity constrained sites
  • Antenna intended for use where data throughput and capacity needs are paramount

Electrical

Ports 6 × Low Band Ports for 694-960 MHz
Frequency Range 694-806 MHz 790-862 MHz 824-896 MHz 880-960 MHz
Gain 18.0 dBi 18.9 dBi 19.1 dBi 19.3 dBi
Azimuth Beamwidth (-3dB) 18.6° 16.8° 16.1° 15.0°
Azimuth Beam Crossover 10.4° 10.5° 10.4° 10.5°
Elevation Beamwidth (-3dB) 17.7° 15.9° 15.2° 14.1°
Electrical Downtilt 4° to 16° 4° to 16° 4° to 16° 4° to 16°
Elevation Sidelobes (1st Upper) < -19 dB < -20 dB < -20 dB < -20 dB
Front-to-Back Ratio @180° > 38 dB > 38 dB > 38 dB > 38 dB
Cross-Polar Port-to-Port Isolation > 24 dB > 24 dB > 24 dB > 24 dB
Interbeam Co-Pol Isolation (Adjacent Beams) (Worst Case) > 15 dB > 15 dB > 15 dB > 15 dB
Interbeam Co-Pol Isolation (Non Adjacent Beams) (Worst Case) > 12 dB > 12 dB > 12 dB > 12 dB
Voltage Standing Wave Ratio (VSWR) < 1.5:1 < 1.5:1 < 1.5:1 < 1.5:1
Passive Intermodulation (2×20W) ≤ -150 dBc ≤ -150 dBc ≤ -150 dBc ≤ -150 dBc
Input Power Continuous Wave (CW) 200 watts 200 watts 200 watts 200 watts
Polarization Dual Pol 45° Dual Pol 45° Dual Pol 45° Dual Pol 45°
Input Impedance 50 ohms 50 ohms 50 ohms 50 ohms
Lightning Protection DC Ground DC Ground DC Ground DC Ground

 

Mechanical

Dimensions (L×W×D) 52.3×53.1×9.8 in (1329×1384×250 mm)
Survival Wind Speed > 150 mph (> 241 kph)
Front Wind Load 592 lbs (2634 N) @ 100 mph (161 kph)
Side Wind Load 121 lbs (539 N) @ 100 mph (161 kph)
Equivalent Flat Plate Area 23.1 ft2 (2.1 m2)
Weight* 124.1 lbs (56.3 kg)
RET Weight 5.0 lbs (2.3 kg)
Connector 6 × 7-16 DIN female long neck or 4.3-10 female
Mounting Poles 2x 2 to 5 in (5 to 12 cm)
Mounting Pole Spacing 31.5 in (800 mm)
* Weight excludes mounting and RET
Bottom View  
   PI MBA3RK4AA BOTTOM
Connector Spacing  
  PI MBA3RK4AA CONNECTOR SPACING
RET to Element Configuration  
   PI MBA3RK4AA RET ELEMENT CONFIG

Typical Antenna Patterns

  For detailed information on additional antenna patterns, contact customer support at
Az EL Blue Red MBA3RK4A AP 734 AZEL10 MBA3RK4A AP 806 AZEL10
  734 MHz Azimuth with Elevation 10° 806 MHz Azimuth with Elevation 10°
 Az EL Blue Red MBA3RK4A AP 925 AZEL10  
  925 MHz Azimuth with Elevation 10°  
MBK-10   MBK-10 Mounting Kit
BSA-RET200   Remote Electrical Tilt System (RET)
HPA-CBK-AG-RRU   RRU AISG cable kit for a 3 RET antenna
HPA-CBK-RA-AG-RRU   RRU AISG right angle cable kit for a 3 RET antenna
SCU-AISG-P   Portable AISG 2.0 Site Control Unit

Software/Firmware

pdficon large HPA-Firmware Upgrade Instructions
 softwareicon Current Firmware

Parts & Accessories

MBA3R-K4AA-K 4 foot (1.3 m) Special Events 3-Beam Antenna with 4.3-10 female connectors, 3 factory installed BSA-RET200 actuators and 2x MBK-10 mounting bracket
MBA3R-K4AB-K 4 foot (1.3 m) Special Events 3-Beam Antenna with 7-16 DIN female long neck connectors , 3 factory installed BSA-RET200 actuators and 2x MBK-10 mounting bracket
MBK-10 Mounting bracket kit (top and bottom) with 0° to 12° mechanical tilt adjustment
BSA-RET200 Remote electrical tilt actuator
HPA-CBK-AG-RRU RRU AISG cable kit for a 3 RET antenna
HPA-CBK-RA-AG-RRU RRU AISG right angle cable kit for a 3 RET antenna

Standards & Compliance

Safety EN 60950-1, UL 60950-1
Emission EN 55022
Immunity EN 55024
Environmental IEC 60068-2-1, IEC 60068-2-2, IEC 60068-2-5, IEC 60068-2-6, IEC-60068-2-11, IEC 60068-2-14, IEC 60068-2-18, IEC 60068-2-27, IEC 60068-2-29, IEC 60068-02-30, IEC 60068-2-52, IEC 60068-2-64, GR-63-CORE 4.3.1, EN 60529, IP 24

Certifications

Antenna Interface Standards Group (AISG), Federal Communication Commission (FCC) Part 15 Class B, CE, CSA US, ISO 9001:2008
 
ISO9001Logo RoHS logo AISGLogo 3GPPLogo
  Footer
              
     
     
       
 

News

CCILogoType

89 Leuning Street

South Hackensack, NJ 07606

+1 (201) 342-3338

+1 (201) 342-3339 fax