Multi-Port Antennas

CCI Portal Login

CCI Customer Portal

In the Americas
   
 
 
 
Sales  
 
 
+1 (201) 342-3338 phone  
+1 (201)-342-3339 fax  
 
89 Leuning Street  
South Hackensack, NJ 07606  
USA  
 
Customer Service  
 
 
+1 (201) 342-3338 phone  
+1 (201)-342-3339 fax  
 
89 Leuning Street  
South Hackensack, NJ 07606  
USA  
 
Technical Support  
 
 
+1 (201) 342-3338 phone  
+1 (201)-342-3339 fax  
 
89 Leuning Street  
South Hackensack, NJ 07606  
USA  
 
 
      Ten Port Multi-Band Antenna DPA65R-KE8A
               
       
       
         
  PI DPA65RKE8A FRONT ISO PI DPA65RKE8A BACK ISO  
  • Eight foot (2.4 m), TriBand, ten port antenna with a 65° azimuth beamwidth covering 698-960 MHz and 1695-2690 MHz frequencies
  • Eight Ultra wide high band ports covering 1695-2690 MHz and two wide low band ports covering 698-960 MHz in a single antenna
  • Full Spectrum Compliance 698-960 MHZ / 1695-2690 MHz
  • Supports Dual 4x4 MIMO in high band
  • LTE Optimized FBR and SPR performance, providing for an efficient use of valuable radio capacity
  • LTE Optimized Boresight and Sector XPD and USL performance, essential for LTE Performance
  • Exceeds minimum PIM performance requirements
  • Equipped with new 4.3-10 connector, which is 40% smaller than traditional 7/16 DIN connector
  • Equipped with 3 field replaceable, integrated AISG 2.0 compliant Remote Electrical Tilt (RET) Controllers (Type 1 External)

Overview

 

The CCI 10-Port TriBand array is a ten port antenna, with eight Ultra Wide high band ports covering 1695-2690 MHz and two Ultra Wide low band ports covering 698-960 MHz. The antenna provides the capability to deploy Dual 4×4 Multiple-input Multiple-output (MIMO) in the high band and 2X2 MIMO across low band ports. The CCI 10-Port allows independent tilt control between the low band ports and high band ports.

In this three RET configuration, the 1st RET is dedicated for the two Low Band ports. The 2nd and 3rd RET are each dedicated to four separate High Band ports. This RET arrangement allows for complete flexibility in coverage control between all eight high band ports.

CCI antennas are designed and produced to ISO 9001:2008 certification standards for reliability and quality in our state-of-the-art manufacturing facilities.

Applications

 
  • Dual 4x4 MIMO on High Band
  • 2x2 MIMO on Low Band
  • Adding additional capacity without adding additional antennas

Electrical

Ports 2 × Low Band Ports for 698-960 MHz
Frequency Range 698-806 MHz 790-862 MHz 824-896 MHz 880-960 MHz
Gain 16.1 dBi 16.3 dBi 16.3 dBi 16.5 dBi
Azimuth Beamwidth (-3dB) 67° 70° 66° 61°
Elevation Beamwidth (-3dB) 10.0° 8.8° 8.5° 7.9°
Electrical Downtilt 0° to 10° 0° to 10° 0° to 10° 0° to 10°
Elevation Sidelobes (1st Upper) <-16 dB <-18 dB <-20 dB <-20 dB
Front-to-Back Ratio @180° > 35 dB > 35 dB > 35 dB > 35 dB
Cross-Polar Discrimination at Peak > 25 dB > 25 dB > 25 dB > 25 dB
Cross-Polar Port-to-Port Isolation > 25 dB > 25 dB > 25 dB > 25 dB
Voltage Standing Wave Ratio (VSWR) < 1.5:1 < 1.5:1 < 1.5:1 < 1.5:1
Passive Intermodulation (2×20W) ≤ -153 dBc ≤ -153 dBc ≤ -153 dBc ≤ -153 dBc
Input Power Continuous Wave (CW) 500 watts 500 watts 500 watts 500 watts
Polarization Dual Linear 45° Dual Linear 45° Dual Linear 45° Dual Linear 45°
Input Impedance 50 ohms 50 ohms 50 ohms 50 ohms
Lightning Protection DC Ground DC Ground DC Ground DC Ground

 

BASTA Electrical Specifications  
Frequency Range 698-806 MHz 790-862 MHz 824-896 MHz 880-960 MHz
Gain over all Tilts (dBi) 15.5 15.7 15.9 16.0
Gain over all Tilts Tolerance (dB) 0.5  0.3  0.5  0.5 
Gain at Low-Tilt (dBi) 15.5 15.7 15.7 15.8
Gain at Mid-Tilt (dBi) 15.7 15.9 16.1 16.3
Gain at High-Tilt (dBi) 15.4 15.6 15.8 16.1
Azimuth Beamwidth Tolerance (°) 2.7 3.5 5.7 1.7
Elevation Beamwidth Tolerance (°) 0.9 0.5 0.6 0.5
Electrical Downtilt Deviation (°) 0.8 0.8 0.7 0.5
First Upper Sidelobe Suppression (dB) 13.7 15.1 16.9 16.5
Upper Sidelobe Suppression Peak to 20°(dB) 15.5 15.0 15.9 15.5
Front-to-Back Ratio over ±20° (dB) 25.6 28.5 28.5 29.0
Cross-polar Discrimination at ±60° (dB) 11.2 11.8 12.4 11.6
* Electrical specifications follow document "Recommendation on Base Station Antenna Standards" (BASTA) V9.6.
All specifications are subject to change without notice.

 

Ports 8 × High Band Ports for 1695-2690 MHz
Frequency Range 1695-1880 MHz 1850-1990 MHz 1920-2180 MHz 2300-2400 MHz 2496-2690 MHz
Gain 16.8 dBi 17.3 dBi 17.4 dBi 17.2 dBi 17.2 dBi
Azimuth Beamwidth (-3dB) 64° 62° 62° 61° 60°
Elevation Beamwidth (-3dB) 8.1° 7.2° 6.7° 5.9° 5.7°
Electrical Downtilt 2° to 10° 2° to 10° 2° to 10° 2° to 10° 2° to 10°
Elevation Sidelobes (1st Upper) <-18 dB <-17 dB <-17 dB <-14 dB <-14 dB
Front-to-Back Ratio @180° > 35 dB > 35 dB > 35 dB > 35 dB > 35 dB
Cross-Polar Discrimination at Peak > 18 dB > 17 dB > 18 dB > 20 dB > 20 dB
Cross-Polar Port-to-Port Isolation > 25 dB > 25 dB > 25 dB > 25 dB > 25 dB
Voltage Standing Wave Ratio (VSWR) < 1.5:1 < 1.5:1 < 1.5:1 < 1.5:1 < 1.5:1
Passive Intermodulation (2×20W) ≤ -153 dBc ≤ -153 dBc ≤ -153 dBc ≤ -153 dBc ≤ -153 dBc
Input Power Continuous Wave (CW) 300 watts 300 watts 300 watts 300 watts 300 watts
Polarization Dual Linear 45° Dual Linear 45° Dual Linear 45° Dual Linear 45° Dual Linear 45°
Input Impedance 50 ohms 50 ohms 50 ohms 50 ohms 50 ohms
Lightning Protection DC Ground DC Ground DC Ground DC Ground DC Ground

 

BASTA Electrical Specifications  
Frequency Range 1695-1880 MHz 1850-1990 MHz 1920-2180 MHz 2300-2400 MHz 2496-2690 MHz
Gain over all Tilts (dBi) 15.9 16.3 16.6 16.3 16.1
Gain over all Tilts Tolerance (dB) 0.5 0.5 0.5 0.6 0.8
Gain at Low-Tilt (dBi) 16.0 16.5 16.7 16.6 16.2
Gain at Mid-Tilt (dBi) 15.9 16.3 16.6 16.4 16.2
Gain at High-Tilt (dBi) 15.8 16.2 16.4 16.0 15.8
Azimuth Beamwidth Tolerance (°) 3.9 3.9 3.8 5.7 5.4
Elevation Beamwidth Tolerance (°) 0.8 0.5 0.5 0.5 0.5
Electrical Downtilt Deviation (°) 1.7 1.6 1.5 1.4 1.4
First Upper Sidelobes Suppression (dB) 14.4 14.3 14.3 11.3 11.2
Upper Sidelobe Suppression Peak to 20°(dB) 12.3 11.7 11.4 10.4 10.9
Front-to-Back Ratio over ±20° (dB) 26.6 26.0 26.0 27.5 27.4
Cross-polar Discrimination at ±60° (dB) 7.6 6.7 6.9 7.1 7.6
* Electrical specifications follow document "Recommendation on Base Station Antenna Standards" (BASTA) V9.6.
All specifications are subject to change without notice.

Mechanical

Dimensions (L×W×D) 96.1×12.1×9.6 in (2441×308×244 mm)
Survival Wind Speed > 150 mph (> 241 kph)
Front Wind Load 297 lbs (1320 N) @ 100 mph (161 kph)
Side Wind Load 246 lbs (1096 N) @ 100 mph (161 kph)
Equivalent Flat Plate Area 11.6 ft2 (1.1 m2)
Weight * 64.6 lbs (29.3 kg)
Connector 10× 4.3-10 Female
Mounting Pole 2 to 5 in (5 to 12 cm)
* Weight excludes mounting 
Bottom View  
  PI DPA65RKE8A BOTTOM Label
Connector Spacing  
  PI DPA65RKE8AA Connector Spacing
RET/Element Configuration  
   PI DPA65RKE8AA RET ELEMENT DIAGRAM

Typical Antenna Patterns

  For detailed information on additional antenna patterns, contact customer support at
Azumuth elevation PI DPA65RKE8A AP 704 AZEL5 PI DPA65RKE8A AP 850 AZEL5
  704 MHz Azimuth with Elevation 5° 850 MHz Azimuth with Elevation 5°
Azumuth elevation PI DPA65RKE8A AP 945 AZEL5  
  945 MHz Azimuth with Elevation 5°  
Highband 8 ports start 2 PI DPA65RKE8A AP 1740 AZEL6 PI DPA65RKE8A AP 1970 AZEL6
  1740 MHz Azimuth with Elevation 6° 1970 MHz Azimuth with Elevation 6°
Highband 8 ports start 2 PI DPA65RKE8A AP 2155 AZEL6 PI DPA65RKE8A AP 2500 AZEL6
  2155 MHz Azimuth with Elevation 6° 2500 MHz Azimuth with Elevation 6°
MBK-01   MBK-01 Mounting Kit
BSA-RET200   Remote Electrical Tilt System (RET)
CBK-AG-RRU-004   AISG Cable set for three RET antenna
CBK-RA-AG-RRU-003   AISG Right Angle Cable set for three RET Antenna
SCU-AISG2-P   Portable AISG 2.0 Site Control Unit

Software/Firmware

pdficon large HPA-Firmware Upgrade Instructions
 softwareicon Current Firmware

Parts & Accessories

DPA65R-KE8AA-K 8 foot (2.4 m) Ten Port antenna with 65° azimuth beamwidth, 4.3-10 female connectors and 3 factory installed external BSA-RET200 RET actuators (Type 1 external) and MBK-01 mounting kit
MBK-01 Mounting bracket kit (top and bottom) with 0° to 10° mechanical tilt adjustment
BSA-RET200 Type 1 remote electrical tilt actuator
CBK-AG-RRU-004 Three RET antenna to RRU AISG cable kit
CBK-RA-AG-RRU-003 Three RET antenna to RRU AISG right angle cable kit

Standards & Compliance

Safety EN 60950-1, UL 60950-1
Emission EN 55022
Immunity EN 55024
Environmental IEC 60068-2-1, IEC 60068-2-2, IEC 60068-2-5, IEC 60068-2-6, IEC-60068-2-11, IEC 60068-2-14, IEC 60068-2-18, IEC 60068-2-27, IEC 60068-2-29, IEC 60068-02-30, IEC 60068-2-52, IEC 60068-2-64, GR-63-CORE 4.3.1, EN 60529, IP 24

Certifications

Antenna Interface Standards Group (AISG), Federal Communication Commission (FCC) Part 15 Class B, CE, CSA US, ISO 9001:2008
 
ISO9001Logo RoHS logo AISGLogo 3GPPLogo
  Footer
              
     
     
       
 

CCILogoType

89 Leuning Street

South Hackensack, NJ 07606

+1 (201) 342-3338

+1 (201) 342-3339 fax