Multi-Port Antennas

CCI Portal Login

CCI Customer Portal

CCI Register

In the Americas
   
 
 
 
Sales  
 
 
+1 (201) 342-3338 phone  
+1 (201)-342-3339 fax  
 
89 Leuning Street  
South Hackensack, NJ 07606  
USA  
 
Customer Service  
 
 
+1 (201) 342-3338 phone  
+1 (201)-342-3339 fax  
 
89 Leuning Street  
South Hackensack, NJ 07606  
USA  
 
Technical Support  
 
 
+1 (201) 342-3338 phone  
+1 (201)-342-3339 fax  
 
89 Leuning Street  
South Hackensack, NJ 07606  
USA  
 
 
      TriBand Antenna HPA45R-KE5A
                
       
       
         
  PI HPA45RKE5AA front iso 20170623  PI HPA45RKE5AA rear iso 20170623  
  • Four and a half foot (1.4 m), TriBand, six port antenna with a 45° azimuth beamwidth covering 698-960 MHz and 1695-2690 MHz frequencies
  • Four wide high band ports covering 1695-2690 MHz and two wide low band ports covering 698-960 MHz in a single antenna
  • New enclosure with <15.4” (391 mm) width, narrowest enclosure in the industry for a 45° TriBand Antenna
  • Full Spectrum Compliance 698-960 MHZ / 1695-2690 MHz
  • LTE Optimized FBR and SPR performance, providing for an efficient use of valuable radio capacity
  • LTE Optimized Boresight and Sector XPD and USL performance, essential for LTE Performance
  • Exceeds minimum PIM performance requirements
  • Comes with 4.3-10 connector, which is 40% smaller than traditional 7/16 DIN connector
  • Ordering options for 2 or 3 field replaceable, integrated AISG 2.0 compliant Remote Electrical Tilt (RET) controllers
   

Overview

 

The CCI TriBand Antenna is a six port antenna, with four wide high band ports covering 1695-2690 MHz and two wide low band ports covering 696-960 MHz. The CCI TriBand Antenna provides the capability to deploy 4×4 Multiple-input Multiple-output (MIMO) in the high band and 2x2 Multiple-input Multiple-output in the low band. The CCI TriBand antenna allows separate tilt control between the low band ports and high band ports. With the use of three (3) RET controllers, the paired high band ports can be tilted independently, enabling maximum flexibility in network deployment.

CCI antennas are designed and produced to ISO 9001:2008 certification standards for reliability and quality in our state-of-the-art manufacturing facilities.

Applications

 
  • 4×4 MIMO for the high band and 2×2 MIMO for the low band
  • Ready for Network Standardization on 4.3-10 DIN connectors
  • With CCI’s TriBand Antennas, wireless providers can connect multiple platforms to a single antenna, reducing tower load, lease expense, deployment time and installation costs

Electrical

Ports 2 × Low Band Ports for 698-960 MHz
Frequency Range 698-806 MHz 790-862 MHz 824-896 MHz 880-960 MHz
Gain 15.4 dBi 15.8 dBi 16.1 dBi 16.6 dBi
Azimuth Beamwidth (-3dB) 52°  50° 47° 44° 
Elevation Beamwidth (-3dB) 16.8°  15.3° 14.7° 13.7°
Electrical Downtilt 2° to 16° 2° to 16° 2° to 16° 2° to 16°
Elevation Sidelobes (1st Upper) <-17 dB <-18 dB <-18 dB <-18 dB
Front-to-Back Ratio @180° > 32 dB > 32 dB > 32 dB > 32 dB
Cross-Polar Discrimination at Peak > 25 dB > 25 dB > 25 dB > 20 dB
Cross-Polar Port-to-Port Isolation > 25 dB > 25 dB > 25 dB > 25 dB
Voltage Standing Wave Ratio (VSWR) < 1.5:1 < 1.5:1 < 1.5:1 < 1.5:1
Passive Intermodulation (2×20W) ≤ -150 dBc ≤ -150 dBc ≤ -150 dBc ≤ -150 dBc
Input Power Continuous Wave (CW) 500 watts 500 watts 500 watts 500 watts
Polarization Dual Linear 45° Dual Linear 45° Dual Linear 45° Dual Linear 45°
Input Impedance 50 ohms 50 ohms 50 ohms 50 ohms
Lightning Protection DC Ground DC Ground DC Ground DC Ground

 

BASTA Electrical Specifications*  
Frequency Range 698-806 MHz 790-862 MHz 824-896 MHz 880-960 MHz
Gain over all Tilts (dBi) 14.8 15.2 15.4 15.6
Gain over all Tilts Tolerance (dB) 0.5 0.5 0.6 0.9
Gain at Low-Tilt (dBi) 15.0 15.4 15.8 16.3
Gain at Mid-Tilt (dBi) 14.8 15.3 15.6 15.8
Gain at High-Tilt (dBi) 14.5  14.8 14.9 14.8 
Azimuth Beamwidth Tolerance (°) 1.5 3.3  3.8  2.1
Elevation Beamwidth Tolerance (°) 1.4 0.8 0.8 0.8
Electrical Downtilt Deviation (°) 1.5 1.2 1.0 1.0
First Upper Sidelobe Suppression (dB) -14.7 -15.9 -17.0 -15.4
Upper Sidelobe Suppression Peak to 20° (dB) -19.0 -19.0 -18.4 -15.6
Front-to-Back Ratio over ±20° (dB) 23.3 25.1 23.8 23.7
Cross-polar Discrimination at 3 dB (dB) 23.0 22.8 21.4 19.8
* Electrical specifications follow document "Recommendation on Base Station Antenna Standards" (BASTA) V9.6.
All specifications are subject to change without notice.

 

Ports 4 × High Band Ports for 1695-2690 MHz
Frequency Range 1695-1880 MHz 1850-1990 MHz 1920-2180 MHz 2300-2400 MHz 2496-2690 MHz
Gain 18.6 dBi 19.2 dBi 19.6 dBi 20.0 dBi 19.7 dBi
Azimuth Beamwidth (-3dB) 45° 44° 43° 43° 35°
Elevation Beamwidth (-3dB) 6.7° 6.1° 5.7° 5.0° 4.8°
Electrical Downtilt 2° to 10° 2° to 10°
2° to 10° 2° to 10° 2° to 10°
Elevation Sidelobes (1st Upper) <-17 dB <-17 dB <-17 dB <-17 dB <-17 dB
Front-to-Back Ratio @180° > 30 dB > 33 dB > 33 dB > 33 dB > 33 dB
Cross-Polar Discrimination at Peak > 20 dB > 20 dB > 20 dB > 20 dB > 20 dB
Cross-Polar Port-to-Port Isolation > 25 dB > 25 dB > 25 dB > 25 dB > 25 dB
Voltage Standing Wave Ratio (VSWR) < 1.5:1 < 1.5:1 < 1.5:1 < 1.5:1 < 1.5:1
Passive Intermodulation (2×20W) ≤ -150 dBc ≤ -150 dBc ≤ -150 dBc ≤ -150 dBc ≤ -150 dBc
Input Power Continuous Wave (CW) 300 watts 300 watts 300 watts 300 watts 300 watts
Polarization Dual Linear 45° Dual Linear 45° Dual Linear 45° Dual Linear 45° Dual Linear 45°
Input Impedance 50 ohms 50 ohms 50 ohms 50 ohms 50 ohms
Lightning Protection DC Ground DC Ground DC Ground DC Ground DC Ground

 

BASTA Electrical Specifications*  
Frequency Range 1695-1880 MHz 1850-1990 MHz 1920-2180 MHz 2300-2400 MHz 2496-2690 MHz
Gain over all Tilts (dBi) 17.7 18.5 18.9 18.9 18.8
Gain over all Tilts Tolerance (dB) 0.6 0.5 0.5 0.5 0.6
Gain at Low-Tilt (dBi) 17.7 18.5 18.9 18.8 19.0
Gain at Mid-Tilt (dBi) 17.7 18.6 19.0 18.9 19.2
Gain at High-Tilt (dBi) 17.7 18.5 18.8 18.6 18.6
Azimuth Beamwidth Tolerance (°) 3.8 3.8 3.9 3.6 3.2
Elevation Beamwidth Tolerance (°) 0.5 0.3 0.6 0.2 0.3
Electrical Downtilt Deviation (°) 0.8 0.8 0.8 0.7 0.8
First Upper Sidelobes Suppression (dB) -15.1 -15.0 -14.8 -14.5 -12.7
Upper Sidelobe Suppression Peak to 20° (dB) -15.0 -14.5 -14.1 -13.2 -12.1
Front-to-Back Ratio over ±20° (dB) 20.3 22.6 24.4 27.9 26.4
Cross-polar Discrimination at 3 dB (dB) 15.7 16.6 17.2 17.9 17.4
* Electrical specifications follow document "Recommendation on Base Station Antenna Standards" (BASTA) V9.6.
All specifications are subject to change without notice.

Mechanical

Dimensions (L×W×D) 55.4×15.4×8.2 in (1407×391×208 mm)
Survival Wind Speed > 150 mph (> 241 kph)
Front Wind Load 189 lbs (842 N) @ 100 mph (161 kph)
Side Wind Load 112 lbs (498 N) @ 100 mph (161 kph)
Equivalent Flat Plate Area 7.4 ft2 (0.7 m2)
Weight * 46.3 lbs (21.0 kg)
RET Weight 3.3 lbs (1.5 kg) for two RET's
RET Weight 5.0 lbs (2.3 kg) for three RET's
Connector 6 × 4.3-10 female
Mounting Pole 2 to 5 in (5 to 12 cm)
* Weight excludes mounting and RET
Bottom View All models
   PI HPA45RKE5AA bottom with labels 20170626

 

Connector Spacing All models
   PI HPA45RKE5A Connector Spacing

 

  HPA45R-KE5AA Element and RET configuration (Type 1 External RET)
   PI HPA45RKE5AA RET ELEMENT DIAGRAM

 

  HPA45R-KE5AB Element and RET configuration (Type 1 External RET)
   PI HPA45RKE5AB RET Element Diagram

Typical Antenna Patterns

  For detailed information on additional antenna patterns, contact customer support at
Azumuth elevation HPA45RKE5A AP 734 AZEL9 HPA45RKE5A AP 860 AZEL9
  734 MHz Azimuth with Elevation 9° 860 MHz Azimuth with Elevation 9°
 Azumuth elevation HPA45RKE5A AP 945 AZEL9  
  945 MHz Azimuth with Elevation 9°  
HPA45RKE5A AP 1850 AZEL6 HPA45RKE5A AP 2110 AZEL6
  1850 MHz Azimuth with Elevation 6° 2110 MHz Azimuth with Elevation 6°
HPA45RKE5A AP 2350 AZEL6 HPA45RKE5A AP 2610 AZEL6
  2350 MHz Azimuth with Elevation 6° 2610 MHz Azimuth with Elevation 6°
MBK-02   MBK-02 Mounting Kit
BSA-RET200   Type 1 External Remote Electrical Tilt System (RET)
TPA-CBK-AG-RRU   RRU AISG cable kit for three RET antenna
DPA-CBK-RA-AG-RRU   RRU AISG right angle cable kit for three RET antenna
CBK-AG-RRU-002   RRU AISG cable kit for two RET antenna
CBK-RA-AG-RRU-002   RRU AISG right angle cable kit for two RET antenna
SCU-AISG-P   Portable AISG 2.0 Site Control Unit

Software/Firmware

pdficon large Firmware Upgrade Instructions
 softwareicon Current Firmware

Parts & Accessories

HPA45R-KE5AA-K Four and a half foot (1.4 m) TriBand antenna with 45° azimuth beamwidth, 4.3-10 female connectors, 3 factory installed BSA-RET200 RET actuators and MBK-02 mounting bracket
HPA45R-KE5AB-K Four and a half foot (1.4 m) TriBand antenna with 45° azimuth beamwidth, 4.3-10 female connectors, 2 factory installed BSA-RET200 RET actuators and MBK-02 mounting bracket
MBK-02 Mounting bracket kit (top and bottom) with 0° to 10° mechanical tilt adjustment
BSA-RET200 Remote electrical tilt actuator
TPA-CBK-AG-RRU HexPort antenna with 3 RET to RRU AISG cable kit
DPA-CBK-RA-AG-RRU HexPort antenna with 3 RET to RRU AISG right angle cable kit
CBK-AG-RRU-002 HexPort antenna with 2 RET to RRU AISG cable kit
CBK-RA-AG-RRU-002 HexPort antenna with 2 RET to RRU AISG right angle cable kit

Standards & Compliance

Safety EN 60950-1, UL 60950-1
Emission EN 55022
Immunity EN 55024
Environmental IEC 60068-2-1, IEC 60068-2-2, IEC 60068-2-5, IEC 60068-2-6, IEC-60068-2-11, IEC 60068-2-14, IEC 60068-2-18, IEC 60068-2-27, IEC 60068-2-29, IEC 60068-02-30, IEC 60068-2-52, IEC 60068-2-64, GR-63-CORE 4.3.1, EN 60529, IP 24

Certifications

Antenna Interface Standards Group (AISG), Federal Communication Commission (FCC) Part 15 Class B, CE, CSA US, ISO 9001:2008
 
ISO9001Logo RoHS logo AISGLogo 3GPPLogo
  Footer
              
     
     
       
 

News

CCILogoType

89 Leuning Street

South Hackensack, NJ 07606

+1 (201) 342-3338

+1 (201) 342-3339 fax