Multi-Port Antennas

CCI Portal Login

CCI Customer Portal

CCI Register

In the Americas
   
 
 
 
Sales  
 
 
+1 (201) 342-3338 phone  
+1 (201)-342-3339 fax  
 
89 Leuning Street  
South Hackensack, NJ 07606  
USA  
 
Customer Service  
 
 
+1 (201) 342-3338 phone  
+1 (201)-342-3339 fax  
 
89 Leuning Street  
South Hackensack, NJ 07606  
USA  
 
Technical Support  
 
 
+1 (201) 342-3338 phone  
+1 (201)-342-3339 fax  
 
89 Leuning Street  
South Hackensack, NJ 07606  
USA  
 
 
      OctoPort Multi-Band Antenna OPA65R-BU4B
                
       
       
         
   PI OPA65RBU4BA front iso  PI OPA65RBU4BA rear iso  
  • Four foot (1.2 m) multiband, eight port antenna with a 65° azimuth beamwidth covering 698-798, 824-896 MHz and 1695-2400 MHz frequencies
  • Four wide high band ports covering 1695-2400 MHz and four frequency specific low band ports covering 698-798 MHz and 824-896 MHz (over a distributed diplexers) in a single antenna
  • New enclosure with <12” (305 mm) width, narrowest enclosure in the industry
  • Full Spectrum Compliance for WCS and AWS-3 frequencies and upcoming Band 14 Operations
  • LTE Optimized FBR and SPR performance, providing for an efficient use of valuable radio capacity
  • LTE Optimized Boresight and Sector XPD and USL performance, essential for LTE Performance
  • Exceeds minimum PIM performance requirements
  • Equipped with new 4.3-10 connector, which is 40% smaller than traditional 7/16 DIN connector
   

Overview

 

The CCI OctoPort multiband array is an eight port antenna, with four wide high band ports covering 1695-2400 MHz and four frequency specific low band ports covering 698-798 MHz and 824-896 MHz. The antenna provides the capability to deploy 4×4 Multiple-input Multiple-output (MIMO) in the high band and 2x2 Multiple-input Multiple-output (MIMO) across each of the paired low band ports.

The CCI OctoPort allows independent tilt control between the low band ports and high band ports, in a three RET Controller (Type 1 External) configuration. The 1st RET is dedicated for the 700 MHz Low Band ports and the 2nd RET is dedicated for the 850 MHz Low Band ports. The 3rd RET is dedicated for the High Band ports. With the use of a single RET in the High Band, equal tilt is achieved across all four High Band ports, which ensures optimal 4x4 MIMO performance.

CCI antennas are designed and produced to ISO 9001:2008 certification standards for reliability and quality in our state-of-the-art manufacturing facilities.

Applications

 
  • 4×4 MIMO for the high band and 2×2 MIMO for the low band
  • Ready for Network Standardization on 4.3-10 DIN connectors
  • With CCI’s multiband antennas, wireless providers can connect multiple platforms to a single antenna, reducing tower load, lease expense, deployment time and installation costs

Electrical

Ports 2 × Low Band Ports for 698-798 MHz 2 × Low Band Ports for 824-896 MHz
Frequency Range 698-798 MHz 824-896 MHz
Gain1 12.5 dBi 12.9 dBi
Gain (Average)2 12.1 dBi 12.3 dBi
Azimuth Beamwidth (-3dB) 68°  68°
Elevation Beamwidth (-3dB) 20.4°  17.7°
Electrical Downtilt 2° to 16° 2° to 16°
Elevation Sidelobes (1st Upper) <-19 dB <-19 dB
Front-to-Back Ratio @180° > 35 dB > 35 dB
Cross-Polar Discrimination at Peak > 25 dB > 25 dB
Cross-Polar Discrimination at 3 dB2 21.7 dB 20.5 dB
Cross-Polar Port-to-Port Isolation > 25 dB > 25 dB
Voltage Standing Wave Ratio (VSWR) < 1.5:1 < 1.5:1
Passive Intermodulation (2×20W) ≤ -150 dBc ≤ -150 dBc
Input Power Continuous Wave (CW) 500 watts 500 watts
Polarization Dual Linear 45° Dual Linear 45°
Input Impedance 50 ohms 50 ohms
Lightning Protection DC Ground DC Ground
1Peak gain across sub-bands.
2Electrical specifications follow document "Recommendation on Base Station Antenna Standards" (BASTA) V9.6.

 

Ports 4 × High Band Ports for 1695-2400 MHz
Frequency Range 1695-1880 MHz 1850-1990 MHz 1920-2180 MHz 2300-2400 MHz
Gain1 16.7 dBi 16.8 dBi 17.1 dBi 16.9 dBi
Gain (Average)2 16.0 dBi 16.3 dBi 16.5 dBi 16.4 dBi
Azimuth Beamwidth (-3dB) 62° 63° 63° 63°
Elevation Beamwidth (-3dB) 8.1° 7.3° 6.8° 6.0°
Electrical Downtilt 2° to 10° 2° to 10° 2° to 10° 2° to 10°
Elevation Sidelobes (1st Upper) <-17 dB <-17 dB <-17 dB <-16 dB
Front-to-Back Ratio @180° > 35 dB > 35 dB > 35 dB > 35 dB
Cross-Polar Discrimination at Peak > 19 dB > 18 dB > 19 dB > 19 dB
Cross-Polar Discrimination at 3 dB2 15.6 dB 15.7 dB 16.4 dB 16.7 dB
Cross-Polar Port-to-Port Isolation > 25 dB > 25 dB > 25 dB > 25 dB
Voltage Standing Wave Ratio (VSWR) < 1.5:1 < 1.5:1 < 1.5:1 < 1.5:1
Passive Intermodulation (2×20W) ≤ -150 dBc ≤ -150 dBc ≤ -150 dBc ≤ -150 dBc
Input Power Continuous Wave (CW) 300 watts 300 watts 300 watts 300 watts
Polarization Dual Linear 45° Dual Linear 45° Dual Linear 45° Dual Linear 45°
Input Impedance 50 ohms 50 ohms 50 ohms 50 ohms
Lightning Protection DC Ground DC Ground DC Ground DC Ground
1Peak gain across sub-bands.
2Electrical specifications follow document "Recommendation on Base Station Antenna Standards" (BASTA) V9.6.

Mechanical

Dimensions (L×W×D) 48.0×11.7×10.1 in (1220×297×256 mm)
Survival Wind Speed > 150 mph (> 241 kph)
Front Wind Load 127 lbs (565 N) @ 100 mph (161 kph)
Side Wind Load 118 lbs (524 N) @ 100 mph (161 kph)
Equivalent Flat Plate Area 5.0 ft2 (0.5 m2)
Weight * 43.0 lbs (19.5 kg)
RET Weight 5.0 lbs (2.3 kg)
Connector 8 × 4.3-10 female
Mounting Pole 2 to 5 in (5 to 12 cm)
* Weight excludes mounting and RET
Bottom View OPA65R-BU4B
  PI OPA65RBU4BA bottom
Connection Spacing Diagram OPA65R-BU4B
  PI OPA65RBU4BA connector spacing
RET to Element Configuration  OPA65R-BU4BA Element and RET configuration
  PI OPA65RBU4BA RET Element Config

Typical Antenna Patterns

  For detailed information on additional antenna patterns, contact customer support at
Posi Neg Red Elevation OPA65RBU4B AP 728 AZEL9 OPA65RBU4B AP 840 AZEL9
  728 MHz Azimuth with Elevation 9° 840 MHz Azimuth with Elevation 9°
 Pos Neg Pos Neg Red Elevation OPA65RBU4B AP 1740 AZEL6 OPA65RBU4B AP 1970 AZEL6
  1740 MHz Azimuth with Elevation 6° 1970 MHz Azimuth with Elevation 6°
Pos Neg Pos Neg Red Elevation OPA65RBU4B AP 2155 AZEL6  
  2155 MHz Azimuth with Elevation 4°  
MBK-02   MBK-02 Mounting Kit
BSA-RET200   Remote Electrical Tilt System (RET) (Type 1 External)
BSA-RET400   Remote Electrical Tilt System (RET) (Type 17 External)
HPA-CBK-AG-RRU   RRU AISG cable kit for three RET antenna
HPA-CBK-RA-AG-RRU   RRU AISG right angle cable kit for three RET antenna
SCU-AISG-P   Portable AISG 2.0 Site Control Unit

Software/Firmware

pdficon large Firmware Upgrade Instructions
 softwareicon Current Firmware

Parts & Accessories

OPA65R-BU4BA-K Four foot (1.2 m) OctoPort antenna with 65° azimuth beamwidth, 4.3-10 female connectors, three factory installed BSA-RET200 RET actuators (Type 1 external) and MBK-02 mounting bracket
OPA65R-BU4BB-K Four foot (1.2 m) OctoPort antenna with 65° azimuth beamwidth, 4.3-10 female connectors, three factory installed BSA-RET400 RET actuators (Type 17 internal) and MBK-02 mounting bracket
MBK-02 Mounting bracket kit (top and bottom) with 0° to 10° mechanical tilt adjustment
BSA-RET200 Remote electrical tilt actuator (Type 1 External)
BSA-RET400 Remote electrical tilt actuator (Type 17 External)
HPA-CBK-AG-RRU RRU AISG cable kit for three RET antenna
HPA-CBK-RA-AG-RRU RRU AISG right angle cable kit for three RET antenna

Standards & Compliance

Safety EN 60950-1, UL 60950-1
Emission EN 55022
Immunity EN 55024
Environmental IEC 60068-2-1, IEC 60068-2-2, IEC 60068-2-5, IEC 60068-2-6, IEC-60068-2-11, IEC 60068-2-14, IEC 60068-2-18, IEC 60068-2-27, IEC 60068-2-29, IEC 60068-02-30, IEC 60068-2-52, IEC 60068-2-64, GR-63-CORE 4.3.1, EN 60529, IP 24

Certifications

Antenna Interface Standards Group (AISG), Federal Communication Commission (FCC) Part 15 Class B, CE, CSA US, ISO 9001:2008
 
ISO9001Logo RoHS logo AISGLogo 3GPPLogo
  Footer
              
     
     
       
 

News

CCILogoType

89 Leuning Street

South Hackensack, NJ 07606

+1 (201) 342-3338

+1 (201) 342-3339 fax