Multi-Port Antennas

CCI Portal Login

CCI Customer Portal

CCI Register

In the Americas
   
 
 
 
Sales  
 
 
+1 (201) 342-3338 phone  
+1 (201)-342-3339 fax  
 
89 Leuning Street  
South Hackensack, NJ 07606  
USA  
 
Customer Service  
 
 
+1 (201) 342-3338 phone  
+1 (201)-342-3339 fax  
 
89 Leuning Street  
South Hackensack, NJ 07606  
USA  
 
Technical Support  
 
 
+1 (201) 342-3338 phone  
+1 (201)-342-3339 fax  
 
89 Leuning Street  
South Hackensack, NJ 07606  
USA  
 
 
      Twelve Port Multi-Band Antenna TPA45R-KU8A
                
       
       
         
  PI TPA45RKU8AA front iso 20170608 PI TPA45RKU8AA rear iso 20170608  
  • Eight foot (2.5 m) multiband, twelve port antenna with a 45° azimuth beamwidth covering 698-960 MHz and 1695-2360 MHz frequencies
  • Eight wide high band ports covering 1695-2360 MHz and four wide low band ports covering 698-960 MHz in a single antenna enclosure
  • New Enclosure, allowing for 15.4” (391mm) width. Narrowest Enclosure in the Industry for a 45° Antenna of this configuration
  • Full Spectrum Compliance for WCS and AWS-3 frequencies and upcoming Band 14 Operations
  • Array configuration allows for 4T4R (4X4 MIMO) on Low Band, essential for Band 14 Operations
  • LTE Optimized FBR and SPR performance, providing for an efficient use of valuable radio capacity
  • LTE Optimized Boresight and Sector XPD and USL performance, essential for LTE Performance
  • Exceeds minimum PIM performance requirements
  • Equipped with new 4.3-10 connector, which is 40% smaller than traditional 7/16 DIN connector
  • Equipped with 3 field replaceable, integrated AISG 2.0 compliant Remote Electrical Tilt (RET) Controllers (Type 1 External)

Overview

 

The CCI 12-Port multiband array is a twelve port antenna, with eight wide high band ports covering 1695-2360 MHz and four wide low band ports covering 698-960 MHz. The antenna provides the capability to deploy Dual 4×4 Multiple-input Multiple-output (MIMO) in the high band and 4X4 Multiple-input Multiple-output (MIMO) across low band ports.

The CCI 12-Port allows independent tilt control between the low band ports and high band ports. With the use of two independent RET controllers in the High Band, the Top and Bottom paired high band ports can be tilted independently, enabling maximum flexibility in network deployment.

CCI antennas are designed and produced to ISO 9001:2008 certification standards for reliability and quality in our state-of-the-art manufacturing facilities.

Applications

 
  • Dual 4×4 MIMO for the High Band and 4X4 MIMO Low Band ports
  • Ready for Network Standardization on 4.3-10 DIN connectors
  • With CCI’s multiband antennas, wireless providers can connect multiple platforms to a single antenna, reducing tower load, lease expense, deployment time and installation costs

Electrical

Ports 4 × Low Band Ports for 698-960 MHz
Frequency Range 698-806 MHz 790-862 MHz 824-896 MHz 880-960 MHz
Gain1 15.2 dBi 15.8 dBi 16.3 dBi 16.4 dBi
Gain (Average)2 14.7 dBi 15.1 dBi 15.5 dBi 15.8 dBi
Azimuth Beamwidth (-3dB) 51° 49° 47° 44°
Elevation Beamwidth (-3dB) 17.8° 15.8° 14.9° 13.8°
Electrical Downtilt 2° to 16° 2° to 16° 2° to 16° 2° to 16°
Elevation Sidelobes (1st Upper) < -18 dB < -18 dB < -18 dB < -18 dB
Front-to-Back Ratio @180° > 30 dB > 30 dB > 30 dB > 30 dB
Cross-Polar Discrimination (at Peak) > 25 dB > 25 dB > 25 dB > 25 dB
Cross-Polar Port-to-Port Isolation > 25 dB > 25 dB > 25 dB > 25 dB
Voltage Standing Wave Ratio(VSWR) < 1.5:1 < 1.5:1 < 1.5:1 < 1.5:1
Passive Intermodulation (2×20W) ≤ -150 dBc ≤ -150 dBc ≤ -150 dBc ≤ -150 dBc
Input Power Continuous Wave (CW) 500 watts 500 watts 500 watts  500 watts
Polarization Dual Pol 45° Dual Pol 45° Dual Pol 45° Dual Pol 45°
Input Impedance 50 ohms 50 ohms 50 ohms 50 ohms
Lightning Protection DC Ground DC Ground DC Ground DC Ground
1Peak gain across sub-bands.
2Electrical specifications follow document "Recommendation on Base Station Antenna Standards" (BASTA) V9.6.

 

Ports 8 × High Band Ports for 1695-2360 MHz
Frequency Range 1695-1880 MHz 1850-1990 MHz 1920-2180 MHz 2305-2360 MHz
Gain1 17.0 dBi 17.6 dBi 18.0 dBi 18.2 dBi
Gain (Average)2 16.2 dBi 16.8 dBi 17.2 dBi 17.3 dBi
Azimuth Beamwidth (-3dB) 45° 45° 43° 41°
Elevation Beamwidth (-3dB) 8.8° 8.1° 7.7° 7.1°
Electrical Downtilt 2° to 10° 2° to 10° 2° to 10° 2° to 10°
Elevation Sidelobes (1st Upper) < -17 dB < -17 dB < -17 dB < -18 dB
Front-to-Back Ratio @180° > 30 dB > 30 dB > 33 dB > 35 dB
Cross-Polar Discrimination (at Peak) > 18 dB > 18 dB > 20 dB > 25 dB
Cross-Polar Port-to-Port Isolation > 25 dB > 25 dB > 25 dB > 25 dB
Voltage Standing Wave Ratio(VSWR) < 1.5:1 < 1.5:1 < 1.5:1 < 1.5:1
Passive Intermodulation (2×20W) ≤ -150 dBc ≤ -150 dBc ≤ -150 dBc ≤ -150 dBc
Input Power Continuous Wave (CW) 300 watts 300 watts 300 watts 300 watts
Polarization Dual Pol 45° Dual Pol 45° Dual Pol 45° Dual Pol 45°
Input Impedance 50 ohms 50 ohms 50 ohms 50 ohms
Lightning Protection DC Ground DC Ground DC Ground DC Ground
1Peak gain across sub-bands.
2Electrical specifications follow document "Recommendation on Base Station Antenna Standards" (BASTA) V9.6.

Mechanical

Dimensions (L×W×D) 98.7×15.4×8.2 in (2507×391×208 mm)
Survival Wind Speed > 150 mph (> 241 kph)
Front Wind Load 371 lbs (1650 N) @ 100 mph (161 kph)
Side Wind Load 225 lbs (1002 N) @ 100 mph (161 kph)
Equivalent Flat Plate Area 14.5 ft2 (1.3 m2)
Weight * 79.4 lbs (36.0 kg)
RET System Weight 5.0 lbs (2.3 kg)
Connector 12 × 4.3-10 female
Mounting Pole 2 to 5 in (5 to 12 cm)
* Weight excludes mounting and RET
Bottom View  
   PI TPA45RKU8AA bottom with labels 20170612
Connector Spacing  
  PI TPA45RKU8AA connector spacing
RET to Array Configuration  
   PI TPA45RKU8A RET Element Config

Typical Antenna Patterns

  For detailed information on additional antenna patterns, contact customer support at
All Ports shown in Azimuith TPA45RKU8A AP 734 AZEL9 TPA45RKU8A AP 860 AZEL9
  734 MHz Azimuth / Elevation 9°  860 MHz Azimuth / Elevation 9°
All Ports shown in Azimuith TPA45RKU8A AP 1780 AZEL6 TPA45RKU8A AP 2155 AZEL6
  1780 MHz Azumth / Elevation 6° 2155 MHz Azumth / Elevation 6°
MBK-01   MBK-01 Mounting Kit
BSA-RET200   Remote Electrical Tilt System (RET) (Type 1)
BSA-RET400   Remote Electrical Tilt System (RET) (Type 17)
TPA-CBK-AG-RRU   AISG Cable set for three RET antenna
TPA-CBK-RA-AG-RRU   AISG Right Angle Cable set for three RET Antenna
SCU-AISG-P   Portable AISG 2.0 Site Control Unit

Software/Firmware

pdficon large HPA-Firmware Upgrade Instructions
 softwareicon Current Firmware

Parts & Accessories

TPA45R-KU8AA-K 8 foot (2.5 m) Twelve Port antenna with 45° azimuth beamwidth, 4.3-10 female connectors, three factory installed BSA-RET200 RET actuators (Type 1 external) and MBK-01 mounting bracket
TPA45R-KU8AB-K 8 foot (2.5 m) Twelve Port antenna with 45° azimuth beamwidth, 4.3-10 female connectors, three factory installed BSA-RET400 RET actuators (Type 17 external) and MBK-01 mounting bracket
MBK-01 Mounting bracket kit (top and bottom) with 0° to 10° mechanical tilt adjustment
BSA-RET200 Type 1 remote electrical tilt actuator
BSA-RET400 Type 17 remote electrical tilt actuator
TPA-CBK-AG-RRU Three RET antenna to RRU AISG cable kit
TPA-CBK-RA-AG-RRU Three RET antenna to RRU AISG right angle cable kit

Standards & Compliance

Safety EN 60950-1, UL 60950-1
Emission EN 55022
Immunity EN 55024
Environmental IEC 60068-2-1, IEC 60068-2-2, IEC 60068-2-5, IEC 60068-2-6, IEC-60068-2-11, IEC 60068-2-14, IEC 60068-2-18, IEC 60068-2-27, IEC 60068-2-29, IEC 60068-02-30, IEC 60068-2-52, IEC 60068-2-64, GR-63-CORE 4.3.1, EN 60529, IP 24

Certifications

Antenna Interface Standards Group (AISG), Federal Communication Commission (FCC) Part 15 Class B, CE, CSA US, ISO 9001:2008
 
ISO9001Logo RoHS logo AISGLogo 3GPPLogo
  Footer
              
     
     
       
 

News

CCILogoType

89 Leuning Street

South Hackensack, NJ 07606

+1 (201) 342-3338

+1 (201) 342-3339 fax