Multi-Port Antennas

CCI Portal Login

CCI Customer Portal

CCI Register

In the Americas
   
 
 
 
Sales  
 
 
+1 (201) 342-3338 phone  
+1 (201)-342-3339 fax  
 
89 Leuning Street  
South Hackensack, NJ 07606  
USA  
 
Customer Service  
 
 
+1 (201) 342-3338 phone  
+1 (201)-342-3339 fax  
 
89 Leuning Street  
South Hackensack, NJ 07606  
USA  
 
Technical Support  
 
 
+1 (201) 342-3338 phone  
+1 (201)-342-3339 fax  
 
89 Leuning Street  
South Hackensack, NJ 07606  
USA  
 
 
      QuadBand Antenna OPA65R-KE6C
                
       
       
         
   PI OPA65RKE6CA front isometric PI OPA65RKE6CA back isometric  
  • Six foot (1.8 m) QuadBand, eight port antenna with a 65° azimuth beamwidth covering 694-862, 876-960 MHz and 1695-2690 MHz frequencies
  • Four wide high band ports covering 1695-2690 MHz and four frequency specific low band ports covering 694-862 MHz and 876-960 MHz (over a non-distributed diplexer) in a single antenna
  • New enclosure with <12” (305 mm) width, narrowest enclosure in the industry
  • Full Spectrum Compliance 694-960 MHZ / 1695-2690 MHz
  • LTE Optimized FBR and SPR performance, providing for an efficient use of valuable radio capacity
  • LTE Optimized Boresight and Sector XPD and USL performance, essential for LTE Performance
  • Exceeds minimum PIM performance requirements
  • Equipped with new 4.3-10 connector, which is 40% smaller than traditional 7/16 DIN connector
  • Ordering options for 2 or 3 field replaceable, integrated AISG 2.0 compliant Remote Electrical Tilt (RET) Controllers (Type 1 External)
   

Overview

 

The CCI QuadBand array is an eight port antenna, with four wide high band ports covering 1695-2690 MHz and four frequency specific low band ports covering 694-862 MHz and 876-960 MHz. The antenna provides the capability to deploy 4×4 Multiple-input Multiple-output (MIMO) in the high band and 2x2 Multiple-input Multiple-output across each of the paired low band ports.

The CCI OctoPort allows independent tilt control between the low band ports and high band ports, with two RET configurations available, either two or three RET Controllers (Type 1 External).
 
In a two RET configuration, the 1st RET is dedicated for the Low Band ports and the 2nd RET is dedicated for the High Band ports. With the use of a single RET in the High Band, equal tilt is achieved across all four High Band ports, which ensures optimal 4x4 MIMO performance.
 
In a three RET configuration, the 1st RET is dedicated for the Low Band ports and the 2nd and 3rd RET is dedicated for the High Band ports. The paired High Band ports can be tilted independently, enabling maximum flexibility in network deployment.

CCI antennas are designed and produced to ISO 9001:2008 certification standards for reliability and quality in our state-of-the-art manufacturing facilities.

Applications

 
  • 4×4 MIMO for the high band and 2×2 MIMO for each of the low bands
  • Ready for Network Standardization on 4.3-10 DIN connectors
  • With CCI’s multiband antennas, wireless providers can connect multiple platforms to a single antenna, reducing tower load, lease expense, deployment time and installation costs

Electrical

Ports 2 × Low Band Ports for 694-862 MHz 2 × Low Band Ports for 876-960 MHz
Frequency Range 694-806 MHz 790-862 MHz 876-960 MHz
Gain 14.2 dBi 14.3 dBi 14.3 dBi
Azimuth Beamwidth (-3dB) 66° 69° 61°
Elevation Beamwidth (-3dB) 12.9° 11.6° 10.4°
Electrical Downtilt 2° to 12° 2° to 12° 2° to 12°
Elevation Sidelobes (1st Upper) <-18 dB <-18 dB <-18 dB
Front-to-Back Ratio @180° > 33 dB > 35 dB > 33 dB
Cross-Polar Discrimination at Peak > 25 dB > 25 dB > 25 dB
Cross-Polar Port-to-Port Isolation > 25 dB > 25 dB > 25 dB
Voltage Standing Wave Ratio (VSWR) < 1.5:1 < 1.5:1 < 1.5:1
Passive Intermodulation (2×20W) ≤ -150 dBc ≤ -150 dBc ≤ -150 dBc
Input Power Continuous Wave (CW) 500 watts 500 watts 500 watts
Polarization Dual Linear 45° Dual Linear 45° Dual Linear 45°
Input Impedance 50 ohms 50 ohms 50 ohms
Lightning Protection DC Ground DC Ground DC Ground

 

BASTA Electrical Specifications*     
Frequency Range 694-806 MHz 790-862 MHz 876-960 MHz
Gain over all Tilts (dBi) 13.8 13.8 14.0
Gain over all Tilts Tolerance (dB) 0.3  0.3  0.5 
Gain at Low-Tilt (dBi) 14.0  14.0  14.2 
Gain at Mid-Tilt (dBi) 13.9  13.9  14.1 
Gain at High-Tilt (dBi) 13.5  13.6  13.7 
Azimuth Beamwidth Tolerance (°) 2.7  5.6  2.9 
Elevation Beamwidth Tolerance (°) 1.1  0.6  0.6 
Electrical Downtilt Deviation (°) 0.7  0.3  0.4 
First Upper Sidelobe Suppression (dB) 16.2 16.9 14.4 
Upper Sidelobe Suppression Peak to 20° (dB) 16.9  18.8  15.6 
Front-to-Back Ratio over ±20° (dB) 24.6 26.0 25.7 
Cross-polar Discrimination at ±60° (dB) 11.8  11.3  12.6 
* Electrical specifications follow document "Recommendation on Base Station Antenna Standards" (BASTA) V9.6.
All specifications are subject to change without notice.

 

Ports 4 × High Band Ports for 1695-2690 MHz
Frequency Range 1695-1880 MHz 1850-1990 MHz 1920-2180 MHz 2300-2400 MHz 2496-2690 MHz
Gain 18.0 dBi 18.3 dBi 18.4 dBi 18.1 dBi 18.2 dBi
Azimuth Beamwidth (-3dB)  63° 62° 62° 61° 61°
Elevation Beamwidth (-3dB) 5.7° 5.1° 4.8° 4.0° 3.8°
Electrical Downtilt  0° to 8°  0° to 8°  0° to 8°  0° to 8°  0° to 8°
Elevation Sidelobes (1st Upper) <-18 dB <-19 dB <-18 dB <-17 dB <-16 dB
Front-to-Back Ratio @180° > 35 dB > 35 dB > 35 dB > 35 dB > 35 dB
Cross-Polar Discrimination at Peak > 18 dB > 17 dB > 18 dB > 18 dB > 18 dB
Cross-Polar Port-to-Port Isolation > 25 dB > 25 dB > 25 dB > 25 dB > 25 dB
Voltage Standing Wave Ratio (VSWR) < 1.5:1 < 1.5:1 < 1.5:1 < 1.5:1 < 1.5:1
Passive Intermodulation (2×20W) ≤ -150 dBc ≤ -150 dBc ≤ -150 dBc ≤ -150 dBc ≤ -150 dBc
Input Power Continuous Wave (CW) 300 watts 300 watts 300 watts 300 watts 300 watts
Polarization Dual Linear 45° Dual Linear 45° Dual Linear 45° Dual Linear 45° Dual Linear 45°
Input Impedance 50 ohms 50 ohms 50 ohms 50 ohms 50 ohms
Lightning Protection DC Ground DC Ground DC Ground DC Ground DC Ground

 

BASTA Electrical Specifications*  
Frequency Range 1695-1880 MHz 1850-1990 MHz 1920-2180 MHz 2300-2400 MHz 2496-2690 MHz
Gain over all Tilts (dBi) 17.2 17.5 17.7 17.3  17.1
Gain Tolerance over all Tilts (dB) 0.5  0.6  0.6  0.6  0.9 
Gain at Low-Tilt (dBi) 17.0  17.1  17.3 16.9  16.7
Gain at Mid-Tilt (dBi) 17.2  17.6 17.9  17.6  17.4 
Gain at High-Tilt (dBi) 17.3  17.8 18.0 17.4  17.2 
Azimuth Beamwidth Tolerance (°) 3.0 3.2 2.9 6.5  4.2
Elevation Beamwidth Tolerance (°) 0.5  0.3  0.3  0.2  0.3 
Electrical Downtilt Deviation (°) 0.5  0.5  0.5  0.6  0.6 
First Upper Sidelobes Suppression (dB) 14.6 15.8 15.6 14.4 13.7
Upper Sidelobe Suppression Peak to 20° (dB) 14.3 14.9  14.0 11.9 12.6 
Front-to-Back Ratio over ±20° (dB) 28.0 29.3 29.9 30.0 30.3
Cross-polar Discrimination at ±60° (dB) 12.4 9.2 9.2 7.0  9.9 
* Electrical specifications follow document "Recommendation on Base Station Antenna Standards" (BASTA) V9.6.
All specifications are subject to change without notice.

Mechanical

Dimensions (L×W×D) 71.1×11.7×8.4 in (1807×297×214 mm)
Survival Wind Speed > 150 mph (> 241 kph)
Front Wind Load 201 lbs (894 N) @ 100 mph (161 kph)
Side Wind Load 160 lbs (714 N) @ 100 mph (161 kph)
Equivalent Flat Plate Area 7.9 ft2 (0.7 m2)
Weight* 56.9 lbs (25.8 kg)
RET Weight 3.3 lbs (1.5 kg) for two RET's
  5.0 lbs (2.3 kg) for three RET's
Connector 8x 4.3-10 female
Mounting Pole 2 to 5 in (5 to 12 cm)
* Weight excludes mounting and RET
Bottom View OPA65R-KE6C
  PI OPA65RKE6CA bottom
 
Connection Spacing Diagram OPA65R-KE6C
  PI OPA65RKE6C Connector Spacing

 

RET to Element Configuration OPA65R-KE6CA Element and RET configuation
  PI OPA65RKE6CA RET Element Config

 

RET to Element Configuration OPA65R-KE6CB Element and RET configuration
  PI OPA65RKE6CB RET Element Config

Typical Antenna Patterns

  For detailed information on additional antenna patterns, contact customer support at
Azumuth elevation OPA65RKE6C AP 728 AZEL7 OPA65RKE6C AP 840 AZEL7
  728 MHz Azimuth with Elevation 7° 840 MHz Azimuth with Elevation 7°
Azumuth elevation OPA65RKE6C AP 945 AZEL7  
  945 MHz Azimuth with Elevation 7°  
Pos Neg Pos Neg Red Elevation OPA65RKE6C AP 1740 AZEL4 OPA65RKE6C AP 1970 AZEL4
  1740 MHz Azimuth with Elevation 4° 1970 MHz Azimuth with Elevation 4°
Pos Neg Pos Neg Red Elevation OPA65RKE6C AP 2155 AZEL4 OPA65RKE6C AP 2500 AZEL4
  2155 MHz Azimuth with Elevation 4° 2500 MHz Azimuth with Elevation 4°
MBK-01   MBK-01 Mounting Kit
BSA-RET200   Remote Electrical Tilt System (RET)
HPA-CBK-AG-RRU   RRU AISG cable kit for 3 RET antenna
HPA-CBK-RA-AG-RRU   RRU AISG right angle cable kit for 3 RET antenna
QPA-CBK-AG-RRU   RRU AISG cable kit for 2 RET antenna
QPA-CBK-RA-AG-RRU   RRU AISG right angle cable kit for 2 RET antenna
SCU-AISG-P   Portable AISG 2.0 Site Control Unit

Software/Firmware

pdficon large Firmware Upgrade Instructions
 softwareicon Current Firmware

Parts & Accessories

OPA65R-KE6CA-K Six foot (1.8 m) OctoPort antenna with 65° azimuth beamwidth, 4.3-10 female connectors, 3 factory installed BSA-RET200 RET actuators and MBK-01 mounting bracket
OPA65R-KE6CB-K Six foot (1.8 m) OctoPort antenna with 65° azimuth beamwidth, 4.3-10 female connectors, 2 factory installed BSA-RET200 RET actuators and MBK-01 mounting bracket
MBK-01 Mounting bracket kit (top and bottom) with 0° to 10° mechanical tilt adjustment
BSA-RET200 Remote electrical tilt actuator
HPA-CBK-AG-RRU RRU AISG cable kit for 3 RET antenna
HPA-CBK-RA-AG-RRU RRU AISG right angle cable kit for 3 RET antenna
QPA-CBK-AG-RRU RRU AISG cable kit for 2 RET antenna
QPA-CBK-RA-AG-RRU RRU AISG right angle cable kit for 2 RET antenna

Standards & Compliance

Safety EN 60950-1, UL 60950-1
Emission EN 55022
Immunity EN 55024
Environmental IEC 60068-2-1, IEC 60068-2-2, IEC 60068-2-5, IEC 60068-2-6, IEC-60068-2-11, IEC 60068-2-14, IEC 60068-2-18, IEC 60068-2-27, IEC 60068-2-29, IEC 60068-02-30, IEC 60068-2-52, IEC 60068-2-64, GR-63-CORE 4.3.1, EN 60529, IP 24

Certifications

Antenna Interface Standards Group (AISG), Federal Communication Commission (FCC) Part 15 Class B, CE, CSA US, ISO 9001:2008
 
ISO9001Logo RoHS logo AISGLogo 3GPPLogo
  Footer
              
     
     
       
 

News

CCILogoType

89 Leuning Street

South Hackensack, NJ 07606

+1 (201) 342-3338

+1 (201) 342-3339 fax