Multi-Port Antennas

CCI Portal Login

CCI Customer Portal

CCI Register

In the Americas
   
 
 
 
Sales  
 
 
+1 (201) 342-3338 phone  
+1 (201)-342-3339 fax  
 
89 Leuning Street  
South Hackensack, NJ 07606  
USA  
 
Customer Service  
 
 
+1 (201) 342-3338 phone  
+1 (201)-342-3339 fax  
 
89 Leuning Street  
South Hackensack, NJ 07606  
USA  
 
Technical Support  
 
 
+1 (201) 342-3338 phone  
+1 (201)-342-3339 fax  
 
89 Leuning Street  
South Hackensack, NJ 07606  
USA  
 
 
      Ten Port Multi-Band Antenna DPA65R-BU6A
                
       
       
         
  PI DPA65RBU6A front iso PI DPA65RBU6A Rear iso  
  • Six foot (1.8 m) multiband, 10 port antenna with a 65° azimuth beamwidth covering 698-896 MHz and 1695-2360 MHz frequencies
  • Full Spectrum Compliance for WCS, AWS3 and upcoming Band 14 Operations
  • LTE Optimized FBR and SPR performance, providing for an efficient use of valuable radio capacity
  • LTE Optimized Boresight and Sector XPD and USL performance, essential for LTE Performance
  • Exceeds minimum PIM performance requirements
  • Equipped with new 4.3-10 connector, which is 40% smaller than traditional 7/16 DIN connector
  • Ordering options for External RET Controllers (Type 1) or Internally Integrated RET Controllers (Type 17)

Overview

 

The CCI DecaPort multiband array is a ten port antenna, with eight wide high band ports covering 1695-2360 MHz and two wide low band ports covering 698-896 MHz. The CCI DecaPort provides the capability to deploy 8×8 Multiple-input Multiple-output (MIMO) or Dual 4x4 Multiple-input Multiple-output (MIMO) in the high band and 2x2 Multiple-input Multiple-output in the low band. The CCI DecaPort allows separate tilt control between the low band ports and high band ports. With the use of two independent RET controllers in the High Band, the Top and Bottom paired high band ports can be tilted independently, enabling maximum flexibility in network deployment.

 

CCI antennas are designed and produced to ISO 9001:2008 certification standards for reliability and quality in our state-of-the-art manufacturing facilities.

Applications

 
  • 8x8 MIMO or Dual 4×4 MIMO for the high band and 2×2 MIMO for the low band
  • With CCI’s multiband antennas, wireless providers can connect multiple platforms to a single antenna, reducing tower load, lease expense, deployment time and installation costs

Electrical

Ports 2 × Low Band Ports for 698-896 MHz
Frequency Range 698-806 MHz 824-896 MHz
Gain Peak1 14.7 dBi 14.7 dBi
Gain (Average)2 14.4 dBi 14.4 dBi
Azimuth Beamwidth (-3dB) 67° 67°
Elevation Beamwidth (-3dB) 12.8° 11.0°
Electrical Downtilt 0° to 10° 0° to 10°
Elevation Sidelobes (1st Upper) < -18 dB < -18 dB
Front-to-Back Ratio @180° > 32 dB > 35 dB
Front-to-Back Ratio over ± 20° > 32dB > 34 dB
Cross-Polar Discrimination at Peak > 25 dB > 25 dB
Cross-Polar Discrimination at sector2 14.1 dB 14.4 dB
Cross-Polar Port-to-Port Isolation > 25 dB > 25 dB
Voltage Standing Wave Ratio(VSWR) < 1.5:1 < 1.5:1
Passive Intermodulation (2×20W) ≤ -150 dBc ≤ -150 dBc
Input Power Continuous Wave (CW) 500 watts 500 watts
Polarization Dual Pol 45° Dual Pol 45°
Input Impedance 50 ohms 50 ohms
Lightning Protection DC Ground DC Ground
1Peak gain across sub-bands.
2Electrical specifications follow document "Recommendation on Base Station Antenna Standards" (BASTA) V9.6.

 

Ports 8 × High Band Ports for 1695-2360 MHz
Frequency Range 1695-1880 MHz 1850-1990 MHz 1920-2180 MHz 2305-2360 MHz
Gain1 15.3 dBi 15.8 dBi 16.2 dBi 16.4 dBi
Gain (Average)2 14.5 dBi 15.2 dBi 15.6 dBi 15.7 dBi
Azimuth Beamwidth (-3dB) 61° 60° 60° 61°
Elevation Beamwidth (-3dB) 11.6° 10.5° 9.8° 8.2°
Electrical Downtilt 2° to 12° 2° to 12° 2° to 12° 2° to 12°
Elevation Sidelobes (1st Upper) < -15 dB < -16 dB < -17 dB < -17 dB
Front-to-Back Ratio @180° > 35 dB > 35 dB > 35 dB > 35 dB
Front-to-Back Ratio over ± 20° > 34 dB > 34 dB > 34 dB > 34 dB
Cross-Polar Discrimination at Peak > 18 dB > 16 dB > 17 dB > 22 dB
Cross-Polar Discrimination at sector2 10.3 dB 9.6 dB 9.3 dB 7.6 dB
Cross-Polar Port-to-Port Isolation > 25 dB > 25 dB > 25 dB > 25 dB
Voltage Standing Wave Ratio(VSWR) < 1.5:1 < 1.5:1 < 1.5:1 < 1.5:1
Passive Intermodulation (2×20W) ≤ -150 dBc ≤ -150 dBc ≤ -150 dBc ≤ -150 dBc
Input Power Continuous Wave (CW) 300 watts 300 watts 300 watts 300 watts
Polarization Dual Pol 45° Dual Pol 45° Dual Pol 45° Dual Pol 45°
Input Impedance 50 ohms 50 ohms 50 ohms 50 ohms
Lightning Protection DC Ground DC Ground DC Ground DC Ground
1Peak gain across sub-bands.
2Electrical specifications follow document "Recommendation on Base Station Antenna Standards" (BASTA) V9.6.

Mechanical

Dimensions (L×W×D) 71.2×11.7×8.4 in (1808×298×214 mm)
Survival Wind Speed > 150 mph (> 241 kph)
Front Wind Load 202 lbs (897 N) @ 100 mph (161 kph)
Side Wind Load 154 lbs (686 N) @ 100 mph (161 kph)
Equivalent Flat Plate Area 7.9 ft2 (0.7 m2)
Weight * 43.0 lbs (19.5 kg)
RET System Weight 5.0 lbs (2.3 kg)
Connector 10 × 4.3-10 female
Mounting Pole 2 to 5 in (5 to 12 cm)
* Weight excludes mounting and RET
Bottom View  
  PI DPA65RBU6A bot with label
Connector Spacing  
  PI DPA65RBU6A connector spacing
RET Element Configuration  
  PI DPA65RBU6AA RET ELEMENT DIA

Typical Antenna Patterns

  For detailed information on additional antenna patterns, contact customer support at
Left Right Red Elevation DPA65RBU6A AP 710 AZEL5 DPA65RBU6A AP 869 AZEL5
  710 MHz Azimuth with Elevation 5° 869 MHz Azimuth with Elevation 5°
Pos Neg Pos Neg Red Elevation DPA65RBU6A AP 1950 AZEL7 DPA65RBU6A AP 2130 AZEL7
  1950 MHz Azimuth with Elevation 7° 2130 MHz Azimuth with Elevation 7°
MBK-01   MBK-01 Mounting Kit
BSA-RET200   Remote Electrical Tilt System (RET)
BSA-RET400   Remote Electrical Tilt System (RET) (Type 17)
DPA-CBK-AG-RRU   AISG Cable set for three RET antenna
DPA-CBK-RA-AG-RRU   AISG Right Angle Cable set for three RET Antenna
SCU-AISG-P   Portable AISG 2.0 Site Control Unit

Software/Firmware

pdficon large HPA-Firmware Upgrade Instructions
 softwareicon Current Firmware

Parts & Accessories

DPA65R-BU6AA-K 6 foot (1.8 m) TenPort antenna with 65° azimuth beamwidth, 4.3-10 female, 3 factory installed BSA-RET200 RET actuators (Type 1 external) and MBK-01 mounting bracket
DPA65R-BU6AB-K 6 foot (1.8 m) TenPort antenna with 65° azimuth beamwidth, 4.3-10 female, 3 factory installed BSA-RET400 RET actuators (Type 17 internal) and MBK-01 mounting bracket
MBK-01 Mounting bracket kit (top and bottom) with 0° to 10° mechanical tilt adjustment
BSA-RET200 Type 1 remote electrical tilt actuator
BSA-RET400 Type 17 remote electrical tilt actuator
DPA-CBK-AG-RRU Three RET antenna to RRU AISG cable kit
DPA-CBK-RA-AG-RRU Three RET antenna to RRU AISG right angle cable kit

Standards & Compliance

Safety EN 60950-1, UL 60950-1
Emission EN 55022
Immunity EN 55024
Environmental IEC 60068-2-1, IEC 60068-2-2, IEC 60068-2-5, IEC 60068-2-6, IEC-60068-2-11, IEC 60068-2-14, IEC 60068-2-18, IEC 60068-2-27, IEC 60068-2-29, IEC 60068-02-30, IEC 60068-2-52, IEC 60068-2-64, GR-63-CORE 4.3.1, EN 60529, IP 24

Certifications

Antenna Interface Standards Group (AISG), Federal Communication Commission (FCC) Part 15 Class B, CE, CSA US, ISO 9001:2008
 
ISO9001Logo RoHS logo AISGLogo 3GPPLogo
  Footer
              
     
     
       
 

News

CCILogoType

89 Leuning Street

South Hackensack, NJ 07606

+1 (201) 342-3338

+1 (201) 342-3339 fax