Multi-Port Antennas

CCI Portal Login

CCI Customer Portal

CCI Register

In the Americas
   
 
 
 
Sales  
 
 
+1 (201) 342-3338 phone  
+1 (201)-342-3339 fax  
 
89 Leuning Street  
South Hackensack, NJ 07606  
USA  
 
Customer Service  
 
 
+1 (201) 342-3338 phone  
+1 (201)-342-3339 fax  
 
89 Leuning Street  
South Hackensack, NJ 07606  
USA  
 
Technical Support  
 
 
+1 (201) 342-3338 phone  
+1 (201)-342-3339 fax  
 
89 Leuning Street  
South Hackensack, NJ 07606  
USA  
 
 
      Low-band Bi-Sector™ Array BSA-S65R-B-H6
                
       
       
         
  DD BSAS65RBH6 front iso 20150729 DD BSAS65RBH6 rear iso 20150729  
  • Patented twin asymmetric beam 33° Bi-Sector array phased arrays over a frequency range of (698-896 MHz), optimized to match existing cloverleaf (65°) deployments.
  • 4 low band ports
  • Single panel design supporting 2 beams
  • Optimized beam shape for maximum LTE data throughput
  • 3GPP/AISG 2.0 compliant
  • Multi band applications – 700 MHz, 800 MHz
  • Provides independent remote control of electrical downtilt for each beam for ease of optimization
   

Overview

 

The CCI Low Band Bi-Sector Antenna is an LTE optimized phased array that provides a total of four low band ports covering the 698 MHz to 896 MHz bands. Our patented bi-sector technology enables the creation of two asymmetric 33° beams each containing two low band ports. The antenna is capable of 2x2 MIMO. The beam shapes have been optimized for minimum overlap and crossover in order to minimize interference across sectors and lower soft handover losses. As such, the antenna array enables maximized data throughput for EVDO, UMTS and LTE networks.

The RET Low Band Bi-Sector Antenna enables operators to remotely control the electrical down-tilt of the antenna in the field with sealed AISG compliant RET actuators. The CCI RET system is designed to meet the reliability, flexibility and efficiency requirements in a wide range of environments. The RET actuators are fully AISG compliant, software upgradeable, daisy chaining capable and fully weather resistant. The remote electrical capability allows independent adjustment of the low band ports each beam for easier optimization.

The single panel design of the antenna array offers the opportunity to reduce antenna count and directly replaces the footprint of an existing 65° antenna. The new coverage that matches the existing footprint minimizes the need for optimization and adjacent site changes, and allows for significant CAPEX and OPEX cost savings.

CCI antennas are designed and produced to ISO 9001:2008 certification standards for reliability and quality in our state-of-the-art manufacturing facilities.

Applications

 
  • Upgrade of data-throughput or capacity constrained sites
  • Spectrum limited markets
  • Deferral of new site builds or carrier adds
  • Spectrum clearing and re-farming

Electrical

Ports 4 × Low Band Ports for 698-896 MHz
Frequency Range 698-806 MHz 824-896 MHz
Gain 16.4 dBi 17.3 dBi
Azimuth Beamwidth (-3dB) 34° 32°
Elevation Beamwidth (-3dB) 11.7° 10.3°
Electrical Downtilt 2° to 12° 2° to 12°
Elevation Sidelobes (1st Upper) < -18 dB < -18 dB
Front-to-Back Ratio @180° > 30 dB > 30 dB
Cross-Polar Discrimination (at Peak) > 24 dB > 25 dB
Cross-Polar Port-to-Port Isolation > 25 dB > 25 dB
Co-Polar Port-to-Port Isolation > 22 dB* > 19 dB
Voltage Standing Wave Ratio (VSWR) < 1.5:1 < 1.5:1
Passive Intermodulation (2×20W) ≤ -153 dBc ≤ -153 dBc
Input Power Continuous Wave (CW) 500 watts 500 watts
Polarization Dual Linear 45° Dual Linear 45°
Input Impedance 50 ohms 50 ohms
Lightning Protection DC Ground DC Ground
*>22 dB from 746-757 MHz; >16 dB elsewhere

 

   
Frequency Range 698-806 MHz 824-896 MHz
Gain over all Tilts (dBi) 16.4 17.3
Gain over all Tilts Tolerance (dB) 0.8 0.7
Gain at Low-tilt (dBi) 16.5 17.5
Gain at Mid-tilt (dBi) 16.4 17.4
Gain at High-tilt (dBi) 16.2 17.0
Azimuth Beamwidth Tolerance (°) 1.8 1.0
Elevation Beamwidth Tolerance (°) 0.9 0.6
Electrical Downtilt Deviation (°) 0.9 1.0
Front-to-Back Ratio over ± 20° (dB) 20.3 28.3
First Upper Sidelobe Suppression (dB) 15.8 14.9
Upper Sidelobe Suppression, peak to 20° (dB) 17.5 16.1
*Electrical specifications follow document "Recommendation on Dase Station Antenna Standards" (BASTA) V9.66
All Specifications are subject to change without notice.

Mechanical

Dimensions (L×W×D) 72.0×28.5×9.7 in (1828×723×245 mm)
Survival Wind Speed > 150 mph (> 241 kph)
Front Wind Load 438 lbs (1947 N) @ 100 mph (161 kph)
Side Wind Load 175 lbs (778 N) @ 100 mph (161 kph)
Equivalent Flat Plate Area 17.1 ft2 (1.6 m2)
Weight * 81.4 lbs (36.9 kg)
RET System Weight 3.3 lbs (1.5 kg)
Connector 4 × 7-16 DIN female long neck
Mounting Pole 2 to 5 in (5 to 12 cm)
* Weight excludes mounting and RET
Bottom View   RET Connection Diagram
  DD BSAS65RBH4H6 bottom with labels 20150729 DD BSAS65RBH4H6 datasheet RET connection diagram small 20151204
Connector Spacing  
  DD BSAS65RBH4H6 CONNECTORDIAGRAM

Typical Antenna Patterns

  For detailed information on additional antenna patterns, contact customer support at
  AP BSAS65RBH6 761 AZEL7 AP BSAS65RBH6 849 AZEL7
  761 MHz Azimuth / Elevation 7°  849 MHz Azimuth / Elevation 7°
Model BSA-RET200   Remote Electrical Tilt System (RET)

Software/Firmware

pdficon large Firmware Upgrade Instructions
 softwareicon Current Firmware

Parts & Accessories

BSA-S65R-B-H6 Six foot (1.8 m), four port, Bi-SectorTM antenna with left and right azimuth beams covering 698-896 MHz.
BSA-S65R-B-H6-K Antenna kit with 2 factory installed RET actuators  and MBK-01 mounting bracket
MBK-01 Mounting bracket kit (top and bottom) with 0° to 10° mechanical tilt adjustment
BSA-RET200 Remote electrical tilt actuator
QPA-CBK-AG-RRU QuadPort antenna to RRU AISG cable kit
QPA-CBK-RA-AG-RRU QuadPort antenna to RRU AISG right angle cable kit

Standards & Compliance

Safety EN 60950-1, UL 60950-1
Emission EN 55022
Immunity EN 55024
Environmental IEC 60068-2-1, IEC 60068-2-2, IEC 60068-2-5, IEC 60068-2-6, IEC-60068-2-11, IEC 60068-2-14, IEC 60068-2-18, IEC 60068-2-27, IEC 60068-2-29, IEC 60068-02-30, IEC 60068-2-52, IEC 60068-2-64, GR-63-CORE 4.3.1, EN 60529, IP 24

Certifications

Antenna Interface Standards Group (AISG), Federal Communication Commission (FCC) Part 15 Class B, CE, CSA US, ISO 9001:2008
 
ISO9001Logo RoHS logo AISGLogo 3GPPLogo
  Footer
              
     
     
       
 

News

CCILogoType

89 Leuning Street

South Hackensack, NJ 07606

+1 (201) 342-3338

+1 (201) 342-3339 fax