Multi-Sector Antennas

CCI Portal Login

CCI Customer Portal

CCI Register

In the Americas
   
 
 
 
Sales  
 
 
+1 (201) 342-3338 phone  
+1 (201)-342-3339 fax  
 
89 Leuning Street  
South Hackensack, NJ 07606  
USA  
 
Customer Service  
 
 
+1 (201) 342-3338 phone  
+1 (201)-342-3339 fax  
 
89 Leuning Street  
South Hackensack, NJ 07606  
USA  
 
Technical Support  
 
 
+1 (201) 342-3338 phone  
+1 (201)-342-3339 fax  
 
89 Leuning Street  
South Hackensack, NJ 07606  
USA  
 
 
      Nine-Beam Special Events Antenna MBA9-6F-U-H3
                
       
       
         
  PI MBA96FUH3 front  
  • Each of nine dual beams optimised for maximum throughput over an impressive range of frequency bands (1710-2360 MHz)
  • Three-foot (0.8 m), single-panel design supports nine beams - without mount changes
  • Each beam is dual +45°/-45° polarized
  • Seperate beams support 9 sub-sectors
  • Rugged, weather resistant, highly reliable design
  • Ultra wideband applications: PCS 1900 MHz, AWS 1710/2170 MHz, WCS 2300 MHz
  • Enables efficient evolution of wireless networks
  • Increases site capacity through higher order sectorization
  • Avoid carrier-adds and building of new capacity sites
  • Boosts data throughput by lowering interference
  • Patented beam shaping technology maximizes coverage
  • Optimized beam crossover and spacing for maximum throughput
     

Overview

 

The CCI Nine-Beam Special Events Antenna is an LTE ready multi-beam antenna that supports multiple sectors (9) from a single antenna. This Nine-Beam Antenna is intended for use at sporting and entertainment venues where social media and the ability to share photos and videos demand high capacity and high data rates. The antenna provides capability for PCS 1900 MHz, AWS 1710/2170 MHz and WCS 2300 MHz coverage in a compact, 3 ft (0.8 m) high single enclosure. This ninebeam antenna has one row of nine dual +45° and -45° cross-polarized beam pairs, each roughly 10 degrees apart that are used to segment large audiences into multiple sectors. The antenna enables maximum spectrum re-use by sectorization, providing as much as nine times increase in network capacity. Our unique beam shaping technology provides fast roll off between beams, minimizing interference between sectors thus increasing the carrier to interference plus noise (CINR) ratio and lowering soft handover losses in LTE, UMTS/HSPA+ and CDMA/EVDO networks.
Such an approach enhances data transfer rates within LTE, UMTS and EVDO network sectors and addresses “hotspots” in mobile wireless operator networks.
The single panel design of the CCI Nine-Beam Special Event Antenna offers the opportunity to reduce antenna count and directly replaces multiple narrow beam antennas. The antenna minimizes the need for optimization as each beam is spaced optimally for maximum throughput thus providing significant CAPEX and OPEX cost savings.


CCI antennas are designed and produced to ISO 9001:2008 certification standards for reliability and quality in our state-of-the-art manufacturing facilities.

Applications

 
  • Upgrade of data-throughput or capacity constrained sites
  • Spectrum limited markets
  • Deferral of CDMA/EVDO or UMTS/HSPA+ carrier adds

Electrical

Ports 18 × High-Band Ports for 1710-2360 MHz
Frequency Range 1850-1990 MHz 1710-1755 MHz/2110-2155 MHz 2305-2360 MHz
Gain 23.9 dBi 22.8 dBi 24.7 dBi 24.6 dBi
Azimuth Beamwidth (-3dB) 9 × 6° 9 × 7° 9 × 5° 9 × 4.8°
Azimuth Beam Crossover -10 dB -10 dB -10 dB -10 dB
Elevation Beamwidth (-3dB) 11.0° 12.5° 10.4° 10.3°
Electrical Downtilt
Elevation Sidelobes (1st Upper) < -18 dB < -18 dB < -18 dB < -17 dB
Front-to-Back Ratio @180° > 30 dB > 30 dB > 30 dB > 30 dB
Cross-Polar Port-to-Port Isolation > 25 dB > 25 dB > 25 dB > 25 dB
Interbeam Co-Pol Isolation > 15 dB > 15 dB > 15 dB > 15 dB
Voltage Standing Wave Ratio(VSWR) < 1.5:1 < 1.5:1 < 1.5:1 < 1.5:1
Passive Intermodulation (2×20W) ≤ -150 dBc ≤ -150 dBc ≤ -150 dBc ≤ -150 dBc
Input Power Continuous Wave Per Port 200 watts 200 watts 200 watts 200 watts
Polarization Dual Pol 45° Dual Pol 45° Dual Pol 45° Dual Pol 45°
Input Impedance 50 ohms 50 ohms 50 ohms 50 ohms
Lightning Protection DC Ground DC Ground DC Ground DC Ground

Mechanical

Dimensions (L×W×D) 33.0×65.3×7.4 in (839×1658×189 mm)
Survival Wind Speed > 125 mph (> 201 kph)
Front Wind Load 460 lbs (2046 N) @ 100 mph (161 kph)
Side Wind Load 56 lbs (250 N) @ 100 mph (161 kph)
Equivalent Flat Plate Area 18.0 ft2 (1.7 m2)
Weight * 99.2 lbs (45.0 kg)
Connector 18 × 7-16 DIN female long neck
Mounting Pole 2 x 2-5 in (5 to 12 cm)
Mounting Pole Spacing 38.4 inches (976 mm) Center to Center
* Weight excludes mounting
Bottom View  
  PI MBA96FUH3 Bottom label
Connector Spacing  
  PI MBA96FUH3 CONNECTORDIAGRAM

Typical Antenna Patterns

For detailed information on additional antenna patterns, contact customer support at
AP MBA96FUH3 1930 AZ AP MBA96FUH3 1930 EL6 
1930 MHz Azimuth 1930 MHz Elevation 6° 
 

Software/Firmware

pdficon large HPA-Firmware Upgrade Instructions
 softwareicon Current Firmware

Parts & Accessories

MBA9-6F-U-H3 3 foot (0.8 m) antenna, Nine-Beam Special Events Ultra-Wideband
MBA9-6F-U-H3-K Complete Kit with Antenna and two MBK-03 mounting brackets
MBK-03(x2) Mounting bracket kit (top and bottom) with 0° to 12° mechanical tilt adjustment

Standards & Compliance

Environmental IEC 60068-2-1, IEC 60068-2-2, IEC 60068-2-5, IEC 60068-2-6, IEC-60068-2-11, IEC 60068-2-14, IEC 60068-2-18, IEC 60068-2-27, IEC 60068-2-29, IEC 60068-02-30, IEC 60068-2-52, IEC 60068-2-64, GR-63-CORE 4.3.1, EN 60529, IP 24

Certifications

Antenna Interface Standards Group (AISG), Federal Communication Commission (FCC) Part 15 Class B, CE, CSA US, ISO 9001:2008
 
ISO9001Logo RoHS logo
  Footer
              
     
     
       
 

News

CCILogoType

89 Leuning Street

South Hackensack, NJ 07606

+1 (201) 342-3338

+1 (201) 342-3339 fax