Multi-Sector Antennas

CCI Portal Login

CCI Customer Portal

CCI Register

In the Americas
   
 
 
 
Sales  
 
 
+1 (201) 342-3338 phone  
+1 (201)-342-3339 fax  
 
89 Leuning Street  
South Hackensack, NJ 07606  
USA  
 
Customer Service  
 
 
+1 (201) 342-3338 phone  
+1 (201)-342-3339 fax  
 
89 Leuning Street  
South Hackensack, NJ 07606  
USA  
 
Technical Support  
 
 
+1 (201) 342-3338 phone  
+1 (201)-342-3339 fax  
 
89 Leuning Street  
South Hackensack, NJ 07606  
USA  
 
 
      Three-Beam Special Events Antenna MBA3F-E3A
                
       
       
         
  PI MBA3FE3A FRONT ISO  
  • Three foot (0.8 m) tall, single band, six port mutlibeam array. Containing Three Independent LTE Optimized Beams covering 1695-2690 MHz frequencies
  • Six High Band Dual-Pol +45°/-45°ports (two ports per beam) covering 1695-2690 MHz in a single antenna
  • Full Spectrum Compliance for 1695-2690 MHz Frequencies
  • LTE Optimized Beams for improved LTE data throughput by minimizing beam crossover, providing for an efficient use of valuable radio capacity and frequency spectrum
  • LTE Optimized FBR, USLS and Co-Pol Beam Isolation Performance. Essential for today’s LTE Data Driven Networks
  • Exceeds minimum PIM performance requirements

Overview

 

This CCI Three-Beam Antenna contains Three Independent LTE Optimized Beams. This Three-Beam Antenna is intended for use at data hotspots and other congested locals, where social media and the ability to share photos and videos and other high demand applications require high capacity and high data rates. This Three-Beam antenna enables maximum spectrum re-use by sectorization, greatly increasing network capacity. Our LTE Optimized Beam Design approach provides fast roll off between beams, minimizing interference between sectors thus increasing the carrier to interference plus noise (CINR) ratio and lowering soft handover losses in LTE networks. Such an approach enhances data transfer rates within LTE network sectors and addresses “hotspots” in mobile wireless operator networks.

The single panel design of the CCI Three-Beam Special Event Antenna offers the opportunity to reduce antenna count and directly replaces multiple narrow beam antennas. The antenna minimizes the need for optimization as each beam is spaced optimally for maximum throughput thus providing significant CAPEX and OPEX cost savings.

 

CCI antennas are designed and produced to ISO 9001:2008 certification standards for reliability and quality in our state-of-the-art manufacturing facilities.

Applications

 
  • Upgrade of data-throughput or capacity constrained sites
  • Antenna intended for use where data throughput and capacity needs are paramount

Electrical

Ports 6 × High Band Ports for 1695-2690 MHz
Frequency Range 1695-1880 MHz 1850-1995 MHz 1920-2180 MHz 2300-2400 MHz 2496-2690 MHz
Gain 18.9 dBi 19.6 dBi 20.1 dBi 21.3 dBi 21.5 dBi
Azimuth Beamwidth (-3dB) 19.7° 17.9° 16.8° 14.3° 12.8°
Azimuth Beam Crossover 11.2 dB 11.1 dB 11.0 dB 11.4 dB 11.0 dB
Elevation Beamwidth (-3dB) 14.5° 13.1° 12.5° 11.0° 9.7°
Electrical Downtilt
Elevation Sidelobes (1st Upper) (Typ.) < -19 dB < -16 dB < -19 dB < -20 dB < -16 dB
Front-to-Back Ratio @180° (Typ.) > 35 dB > 35 dB > 35 dB > 35 dB > 35 dB
Cross-Polar Discrimination (at Peak) > 22 dB > 22 dB > 21 dB > 20 dB > 19 dB
Cross-Polar Port-to-Port Isolation > 24 dB > 24 dB > 24 dB > 24 dB > 24 dB
Interbeam Co-Pol Isolation > 15 dB > 15 dB > 15 dB > 15 dB > 15 dB
Interbeam Co-Pol isolation (Non-Adjacent Beams) (Worse Case) > 12 dB > 12 dB > 10 dB > 12 dB > 12 dB
Voltage Standing Wave Ratio(VSWR) < 1.5:1 < 1.5:1 < 1.5:1 < 1.5:1 < 1.5:1
Passive Intermodulation (2×20W) ≤ -150 dBc ≤ -150 dBc ≤ -150 dBc ≤ -150 dBc ≤ -150 dBc
Input Power Continuous Wave (CW) 200 watts 200 watts 200 watts 200 watts 200 watts
Polarization Dual Pol 45° Dual Pol 45° Dual Pol 45° Dual Pol 45° Dual Pol 45°
Input Impedance 50 ohms 50 ohms 50 ohms 50 ohms 50 ohms
Lightning Protection DC Ground DC Ground DC Ground DC Ground DC Ground

Mechanical

Dimensions (L×W×D) 30.5×24.9×7.2 in (776×633×169 mm)
Survival Wind Speed > 150 mph (> 241 kph)
Front Wind Load 343 lbs (1525 N) @ 100 mph (161 kph)
Side Wind Load 53 lbs (237 N) @ 100 mph (161 kph)
Equivalent Flat Plate Area 13.4 ft2 (1.2 m2)
Weight * 41.6 lbs (18.9 kg)
Connector 6× 7-16 DIN female long neck or 4.3-10 female
Mounting Pole 2 to 5 in (5 to 12 cm)
* Weight excludes mounting
Bottom View  
   PI MBA3FE3A BOTTOM
Connector Spacing  
   PI MBA3FE3A CONNECTOR SPACING

Typical Antenna Patterns

  For detailed information on additional antenna patterns, contact customer support at
Az EL MBA3FE3A AP 1930 AZ MBA3FE3A AP 1930 EL6
  1930 MHz Azimuths 1930 MHz Elevation 6°
Az EL  MBA3FE3A AP 2360 AZ MBA3FE3A AP 2360 EL6
  2360 MHz Azimuths 2360 MHz Elevation 6°
Az EL  MBA3FE3A AP 2650 AZ MBA3FE3A AP 2650 EL6
  2650 MHz Azimuths 2650 MHz Elevation 6°
 

Software/Firmware

pdficon large HPA-Firmware Upgrade Instructions
 softwareicon Current Firmware

Parts & Accessories

MBA3F-E3AA-K 3 foot (0.8 m) Special Events 3-Beam Antenna with fixed electrical tilt, 7-16 DIN connectors and MBK-03 mounting bracket.
MBA3F-E3AB-K 3 foot (0.8 m) Special Events 3-Beam Antenna with fixed electrical tilt, 4.3-10 connectors and  MBK-03 mounting bracket.
MBK-03 Mounting bracket kit (top and bottom) with 0° to 12° mechanical tilt adjustment

Standards & Compliance

Environmental IEC 60068-2-1, IEC 60068-2-2, IEC 60068-2-5, IEC 60068-2-6, IEC-60068-2-11, IEC 60068-2-14, IEC 60068-2-18, IEC 60068-2-27, IEC 60068-2-29, IEC 60068-02-30, IEC 60068-2-52, IEC 60068-2-64, GR-63-CORE 4.3.1, EN 60529, IP 24

Certifications

Federal Communication Commission (FCC) Part 15 Class B, ISO 9001:2008
 
ISO9001Logo RoHS logo
  Footer
              
     
     
       
 

News

CCILogoType

89 Leuning Street

South Hackensack, NJ 07606

+1 (201) 342-3338

+1 (201) 342-3339 fax