Multi-Sector Antennas

CCI Portal Login

CCI Customer Portal

In the Americas
+1 (201) 342-3338 phone  
+1 (201)-342-3339 fax  
89 Leuning Street  
South Hackensack, NJ 07606  
Customer Service  
+1 (201) 342-3338 phone  
+1 (201)-342-3339 fax  
89 Leuning Street  
South Hackensack, NJ 07606  
Technical Support  
+1 (201) 342-3338 phone  
+1 (201)-342-3339 fax  
89 Leuning Street  
South Hackensack, NJ 07606  
      Six-Beam Special Events Antenna MBA6-9F-P-H3
  • Six dual beams optimised for maximum throughput over the PCS band
  • Three foot (0.9 m), single-panel design supports six beams - without mount changes
  • Each beam pair dual +45°/-45° polarized
  • Seperate beams support 6 sub-sectors
  • Rugged, weather resistant, highly reliable design
  • Enables efficient evolution of wireless networks
  • Increases site capacity through higher order sectorization
  • Avoid carrier-adds and building of new capacity sites
  • Boosts data throughput by lowering interference
  • Patented beam shaping technology maximizes coverage
  • Optimized beam crossover and spacing for maximum throughput



The CCI Six-Beam Special Events Antenna is an LTE ready multi-beam antenna that supports multiple sectors (6) from a single antenna. This Six-Beam Antenna is intended for use at sporting and entertainment venues where social media and the ability to share photos and videos demand high capacity and high data rates. The antenna provides capability for PCS 1900 MHz coverage in a compact, 3 ft (0.9 m) high single enclosure. This six-beam antenna has one row of six dual +45° and -45° cross-polarized beam pairs, each roughly 15 degrees apart that are used to segment large audiences into multiple sectors. The antenna enables maximum spectrum re-use by sectorization, providing as much as nine times increase in network capacity. Our unique beam shaping technology provides fast roll off between beams, minimizing interference between sectors thus increasing the carrier to interference plus noise (CINR) ratio and lowering soft handover losses in LTE, UMTS/HSPA+ and CDMA/EVDO networks. Such an approach enhances data transfer rates within LTE, UMTS and EVDO network sectors and addresses “hotspots” in mobile wireless operator networks.
The single panel design of the CCI Six-Beam Special Event Antenna offers the opportunity to reduce antenna count and directly replaces multiple narrow beam antennas. The antenna minimizes the need for optimization as each beam is spaced optimally for maximum throughput thus providing significant CAPEX and OPEX cost savings.
CCI antennas are designed and produced to ISO 9001:2008 certification standards for reliability and quality in our state-of-the-art manufacturing facilities.


  • Upgrade of data-throughput or capacity constrained sites
  • Spectrum limited markets
  • Deferral of CDMA/EVDO or UMTS/HSPA+ carrier adds
  • Spectrum clearing and refarming


Ports 12 × High-Band Ports for 1850-1995 MHz
Gain 22.7 dBi
Azimuth Beamwidth (-3dB) 9.0°
Azimuth Beam Crossover -10.5 dB
Elevation Beamwidth (-3dB) 11.2°
Electrical Downtilt
Elevation Sidelobes (1st Upper) < -21 dB
Front-to-Back Ratio @180° > 35 dB
Cross-Polar Port-to-Port Isolation > 30 dB
Interbeam Co-Pol Isolation (Adjacent Beams) >15 dB
Interbeam Co-Pol Isolation (Non-Adjacent Beams) >12.5 dB
Voltage Standing Wave Ratio(VSWR) < 1.5:1
Passive Intermodulation (2×20W) ≤ -153 dBc
Input Power Continuous Wave (CW) 300 watts
Polarization Dual Pol 45°
Input Impedance 50 ohms
Lightning Protection DC Ground


Dimensions (L×W×D) 35.0×45.9×6.4 in (890×1165×163 mm)
Survival Wind Speed > 125 mph (> 201 kph)
Front Wind Load 343 lbs (1525 N) @ 100 mph (161 kph)
Side Wind Load 53 lbs (237 N) @ 100 mph (161 kph)
Equivalent Flat Plate Area 13.4 ft2 (1.2 m2)
Weight * 72.6 lbs (32.9 kg)
Connector 12 × 7-16 DIN female long neck
Mounting Pole 2x 2 to 5 in (5 to 12 cm)
* Weight excludes mounting
Bottom View  
  PI MBA69FPH3 Bottom label
Connector Spacing  

Typical Antenna Patterns

  For detailed information on additional antenna patterns, contact customer support at
  AP MBA69FPH3 1930 AZ  AP MBA69FPH3 1930 EL4
  1930 MHz Azimuth 1930 MHz Elevation 6° 


pdficon large HPA-Firmware Upgrade Instructions
 softwareicon Current Firmware

Parts & Accessories

MBA6-9F-P-H3 Three foot (0.9 m) Special Events Six-Beam Antenna with Fixed Electrical Tilt
MBA6-9F-P-H3-K Antenna kit with three foot (0.9 m) Antenna and 2X MBK-03 Mounting Bracket
MBK-03 x 2 Mounting bracket kit (top and bottom) with 0° to 12° mechanical tilt adjustment

Standards & Compliance

Environmental IEC 60068-2-1, IEC 60068-2-2, IEC 60068-2-5, IEC 60068-2-6, IEC-60068-2-11, IEC 60068-2-14, IEC 60068-2-18, IEC 60068-2-27, IEC 60068-2-29, IEC 60068-02-30, IEC 60068-2-52, IEC 60068-2-64, GR-63-CORE 4.3.1, EN 60529, IP 24


Antenna Interface Standards Group (AISG), Federal Communication Commission (FCC) Part 15 Class B, CE, CSA US, ISO 9001:2008
ISO9001Logo RoHS logo


89 Leuning Street

South Hackensack, NJ 07606

+1 (201) 342-3338

+1 (201) 342-3339 fax