Multi-Sector Antennas

CCI Portal Login

CCI Customer Portal

CCI Register

In the Americas
   
 
 
 
Sales  
 
 
+1 (201) 342-3338 phone  
+1 (201)-342-3339 fax  
 
89 Leuning Street  
South Hackensack, NJ 07606  
USA  
 
Customer Service  
 
 
+1 (201) 342-3338 phone  
+1 (201)-342-3339 fax  
 
89 Leuning Street  
South Hackensack, NJ 07606  
USA  
 
Technical Support  
 
 
+1 (201) 342-3338 phone  
+1 (201)-342-3339 fax  
 
89 Leuning Street  
South Hackensack, NJ 07606  
USA  
 
 
      Ten/Five-Beam Special Events Antenna MBA10-5F-BW-H3
                
       
       
         
  PI MBA105FBWH3 Front iso  
  • Five low band beams optimized for maximum throughput over frequency bands (698-896 MHz); Ten high band beams optimized for maximum throughput over frequency bands (1695-2180 MHz)
  • Three foot (1.0 m), single panel, fifteen beam design without mount changes
  • Dual +/- 45° cross-polarization for each beam pair
  • Separate beams support 5 low band and 10 high-band sub-sectors
  • Simultaneous High Band PCS 1900 MHz, AWS 1695/2180 and Low Band LTE 700 MHz, SMR 850 MHz and Cellular 850 Coverage. 
  • Enables efficient evolution of wireless networks. 
  • Increases site capacity through high order sectorization.
  • Avoid carrier-adds and building of new capacity sites.
  • Boosts data throughput by lowering interference.
  • Patented beam shaping technology maximizes coverage
  • Optimized beam crossover and spacing for maximum throughput

Overview

 

The CCI Ten/Five-Beam Special Events Antenna is an LTE ready multi-beam, multi-band antenna that simultaneously supports (10) high band and (5) low band sectors from a single antenna. This Ten/Five-Beam Antenna is intended for use at sporting and entertainment venues where social media and the ability to share photos and videos demand high capacity and high data rates. The high band ports provide coverage for PCS 1900 MHz and AWS 1695/2180 MHz bands while the low band ports provide LTE 700 MHz, SMR 800 and Cellular 850 MHz capability in a  compact, 3 ft (1.0 m) high single enclosure. Each beam is fed by a pair of +45° and -45° cross-polarized ports. The high band beams are each roughly 15 degrees apart and each pair are evenly juxtaposed  on the five low band beams. This antenna segments large audiences into multiple sectors thus enabling maximum spectrum re-use by sectorization, providing as much as nine times increase in network capacity. Our unique beam shaping technology provides fast roll off between beams, minimizing interference between sectors thus increasing the carrier to interference plus noise (CINR) ratio and lowering soft handover losses in LTE, UMTS/HSPA+ and CDMA/EVDO networks. Such an approach enhances data transfer rates within LTE, UMTS and EVDO network sectors and addresses “hotspots” in mobile wireless operator networks.

The single panel design of the CCI Ten/Five-Beam Special Event Antenna offers the opportunity to reduce antenna count and directly replaces multiple narrow beam antennas. The antenna minimizes the need for optimization as each beam is spaced optimally for maximum throughput thus providing significant CAPEX and OPEX cost savings.

CCI antennas are designed and produced to ISO 9001:2008 certification standards for reliability and quality in our state-of-the-art manufacturing facilities.

Applications

 
  • Upgrade of data-throughput or capacity constrained sites
  • Antenna intended for use at sporting and entertainment venues

Electrical

Ports 10 × Low Band Ports for 698-896 MHz 20 × High Band Ports for 1695-2180 MHz
Frequency Range 698-806 MHz 824-896 MHz 1850-1990 MHz 1695-1780/2110-2180 MHz
Gain 19.0 dBi 19.7 dBi 23.9 dBi 22.8 dBi 24.4 dBi
Azimuth Beamwidth (-3dB) 5 x 11.6° 5 x 9.9° 10 x 5.3° 10 x 5.9° 10 x 4.6°
Azimuth Beam Crossover (Typ.) -10 dB -10 dB -10 dB -10 dB -10 dB
Elevation Beamwidth (-3dB) 22.2° 19.7° 11.4° 12.6° 10.3°
Electrical Downtilt
Elevation Sidelobes (1st Upper) < -26 dB < -24 dB < -20 dB < -20 dB < -18 dB
Front-to-Back Ratio @180° > 40 dB > 40 dB > 40 dB > 40 dB > 40 dB
Cross-Polar Port-to-Port Isolation > 25 dB > 25 dB > 25 dB > 25 dB > 25 dB
Co-Polar Isolation1 (Adjacent Beams) > 25 dB > 25 dB > 25 dB > 25 dB > 25 dB
Co-Polar Isolation (Non-Adjacent Beams) > 15 dB > 15 dB > 11 dB > 15 dB > 15 dB
Voltage Standing Wave Ratio(VSWR) < 1.5:1 < 1.5:1 < 1.5:1 < 1.5:1 < 1.5:1
Passive Intermodulation (2×20W) ≤ -153 dBc ≤ -153 dBc ≤ -153 dBc ≤ -153 dBc ≤ -153 dBc
Input Power Continuous Wave per Port 200 watts 200 watts 200 watts 200 watts 200 watts
Polarization Dual Linear 45° Dual Linear 45° Dual Linear 45° Dual Linear 45° Dual Linear 45°
Input Impedance 50 ohms 50 ohms 50 ohms 50 ohms 50 ohms
Lightning Protection DC Ground DC Ground DC Ground DC Ground DC Ground
1 Worst-case between any pair of Adjacent Beams, averaged over frequency band.

 

BASTA Electrical Specifications*    
Frequency Range 698-806 MHz 824-896 MHz 1850-1990 MHz 1695-1780/2110-2180 MHz
Gain (dBi) 18.8 19.6 23.8 22.7 24.4
Gain Tolerance (dBi) 1.0 0.9 1.0 1.0 0.7
Azimuth Beamwidth Tolerance (°) 2.0 1.3 0.8 1.2 0.5
Elevation Beamwidth Tolerance (°) 1.4 1.4 0.6 0.4 0.4
Electrical Downtilt Deviation (°) 1.3 1.6 0.7 0.9 0.6
Front-to-Back Ratio over ± 20° (dB) 31.1 30.9 34.4 35.4 35.4
First Upper Sidelobe Suppression (dB) 20.0 22.0 17.9 16.9 17.1
Upper Sidelobe Suppression peak to 20°(dB) NA NA 18.5 18.5 17.6
* Electrical specifications follow document "Recommendation on Base Station Antenna Standards" (BASTA) V9.6.
All specifications are subject to change without notice.

Mechanical

Dimensions (L×W×D) 40.8×83.0×11.3 in (1036×2109×286 mm)
Survival Wind Speed > 150 mph (> 241 kph)
Front Wind Load 722 lbs (3214 N) @ 100 mph (161 kph)
Side Wind Load 102 lbs (454 N) @ 100 mph (161 kph)
Equivalent Flat Plate Area 28.2 ft2 (2.6 m2)
Weight* 157.4 lbs (71.4 kg)
Connector 30 × 7-16 DIN female long neck
Mounting Pole 2x 2 to 5 in (5 to 12 cm)
Mounting Pole Spacing 38.4 in (976 mm)
* Weight excludes mounting
Bottom View  
   PI MBA105FBWH3 bottom labelnew
Connector Spacing  
   PI MBA105FBWH3 connector spacing

Typical Antenna Patterns

  For detailed information on additional antenna patterns, contact customer support at
  MBA105FBWH3 AP 824 AZEL6 MBA105FBWH3 AP 1930 AZEL4
  824 MHz Azimuth / Elevation 6° 1930 MHz Azimuth / Elevation 4°
 

Software/Firmware

pdficon large HPA-Firmware Upgrade Instructions
 softwareicon Current Firmware

Parts & Accessories

MBA10-5F-BW-H3 3' (1.0 m) Antenna, Ten-Five Beam Special Events Antenna with fixed electrical tilt
MBA10-5F-BW-H3-K Antenna kit with 3' (1.0 m) Antenna and 2 MBK-03 Mounting Brackets
MBK-03 x 2 Mounting bracket kit (top and bottom) with 0° to 12° mechanical tilt adjustment

Standards & Compliance

Environmental IEC 60068-2-1, IEC 60068-2-2, IEC 60068-2-5, IEC 60068-2-6, IEC-60068-2-11, IEC 60068-2-14, IEC 60068-2-18, IEC 60068-2-27, IEC 60068-2-29, IEC 60068-02-30, IEC 60068-2-52, IEC 60068-2-64, GR-63-CORE 4.3.1, EN 60529, IP 24

Certifications

Federal Communication Commission (FCC) Part 15 Class B, CE, CSA US, ISO 9001:2008
 
ISO9001Logo RoHS logo
  Footer
              
     
     
       
 

News

CCILogoType

89 Leuning Street

South Hackensack, NJ 07606

+1 (201) 342-3338

+1 (201) 342-3339 fax