Bi-Sector Array Antennas

CCI Portal Login

CCI Customer Portal

CCI Register

In the Americas
   
 
 
 
Sales  
 
 
+1 (201) 342-3338 phone  
+1 (201)-342-3339 fax  
 
89 Leuning Street  
South Hackensack, NJ 07606  
USA  
 
Customer Service  
 
 
+1 (201) 342-3338 phone  
+1 (201)-342-3339 fax  
 
89 Leuning Street  
South Hackensack, NJ 07606  
USA  
 
Technical Support  
 
 
+1 (201) 342-3338 phone  
+1 (201)-342-3339 fax  
 
89 Leuning Street  
South Hackensack, NJ 07606  
USA  
 
 
      Wideband Bi-SectorTM Array BSA33R-U3A
                
       
       
         
  PI BSA33RU3A FRONT ISO  PI BSA33RU3A REAR ISO  
  • Three foot (0.9 m), Wideband, eight port Bi-Sector Antenna. Deploying a high performing two pairs of CCI’s Patented Asymmetrical 33° Shaped Beams covering 1695-2400 MHz frequencies
  • Eight wide High Band ports (4 ports per beam) covering 1695-2400 MHz and in a single antenna
  • Full Spectrum Compliance for 1695-2400 MHz Operations
  • LTE Optimized Asymmetric Shaped Beams for improved LTE data throughput by minimizing beam crossover, providing for an efficient use of valuable radio capacity and frequency spectrum
  • LTE Optimized FBR, SPR and Boresight/Sector XPD Performance, essential for today’s LTE Data Networks
  • Exceeds minimum PIM performance requirements
  • Equipped with new 4.3-10 connector, which is 40% smaller than traditional 7/16 DIN connector
  • Equipped with Two Field Replaceable, integrated AISG 2.0 compliant Remote Electrical Tilt (RET)

Overview

 

This version of the CCI Bi-Sector Wideband Array is an eight port antenna, with eight wide High Band ports (four per beam) covering 1695-2400 MHz. The CCI Bi-Sector array uses a two pairs of CCI’s High Performing Patented Asymmetric 33° Shaped Beams in the High Band frequencies. The CCI Bi-Sector Array thus provides the capability to deploy Dual (over split beams) 4×4 Multiple-input Multiple-output (MIMO) in the High Band. The CCI Bi-Sector Array utilizes two RET controllers, with a separate RET controller for each of CCI’s Patented Asymmetric 33° Shaped Beams.

 

The CCI Bi-Sector Wideband Array, allow operators to reduce antenna count and replace existing 65° networks, while increasing cell site capacity and LTE data throughput by minimizing overlap between CCI’s Patented Asymmetric 33° Shaped Beams. This design approach lowers interference between sectors. All of this is achieved through a single panel array, producing significant CAPEX and OPEX cost savings for the operator.

 

CCI antennas are designed and produced to ISO 9001:2008 certification standards for reliability and quality in our state-of-the-art manufacturing facilities.

Applications

 
  • With CCI’s Bi-Sector Wideband Antenna, wireless operators can connect multiple platforms to a single antenna, reducing tower load, lease expense, deployment time and installation cost
  • Ideal Antenna Solution for structurally constrained sites, where data throughput, capacity and limited spectrum is a concern
  • Quad (over split beams) 4x4 MIMO in High Band
  • Ready for Network Standardization on 4.3-10 connectors

Electrical

Ports 8 × High Band Ports for 1695-2400 MHz
Frequency Range 1695-1880 MHz 1850-1990 MHz 1920-2180 MHz 2300-2400 MHz
Gain1 17.2 dBi 17.8 dBi 18.5 dBi 19.0 dBi
Gain (Average)2 16.5 dBi 17.2 dBi 17.6 dBi 18.4 dBi
Azimuth Beamwidth (-3 dB) 39° 36° 34° 30°
Azimuth Peak Offset 31° 30° 29° 26°
Elevation Beamwidth (-3 dB) 9.9° 9.0° 8.6° 7.7°
Electrical Downtilt 0° to 10° 0° to 10° 0° to 10° 0° to 10°
Elevation Sidelobes (1st Upper) < -17 dB < -17 dB < -17 dB < -20 dB
Front-to-Back Ratio @180° > 35 dB > 35 dB > 35 dB > 35 dB
Front-to-Back Ratio over ± 20° > 33 dB > 33 dB > 33 dB > 30 dB
Cross-Polar Discrimination (at Peak) > 25 dB > 24 dB > 23 dB > 23 dB
Cross-Polar Discrimination (at 3 dB)2 15.7 dB 14.6 dB 13.1 dB 13.1 dB
Cross-Polar Port-to-Port Isolation > 25 dB > 25 dB > 25 dB > 25 dB
Voltage Standing Wave Ratio(VSWR) < 1.5:1 < 1.5:1 < 1.5:1 < 1.5:1
Passive Intermodulation (2×20W) ≤ -150 dBc ≤ -150 dBc ≤ -150 dBc ≤ -150 dBc
Input Power Continuous Wave (CW) 300 watts 300 watts 300 watts 300 watts
Polarization Dual Pol 45° Dual Pol 45° Dual Pol 45° Dual Pol 45°
Input Impedance 50 ohms 50 ohms 50 ohms 50 ohms
Lightning Protection DC Ground DC Ground DC Ground DC Ground
1Peak gain across sub-bands.
2Electrical specifications follow document "Recommendation on Base Station Antenna Standards" (BASTA) V9.6.

Mechanical

Dimensions (L×W×D) 37.4×24.0×6.2 in (949×610×158 mm)
Survival Wind Speed > 150 mph (> 241 kph)
Front Wind Load 191 lbs (851 N) @ 100 mph (161 kph)
Side Wind Load 56 lbs (249 N) @ 100 mph (161 kph)
Equivalent Flat Plate Area 7.5 ft2 (0.7 m2)
Weight*
42.3 lbs (19.2 kg)
RET System Weight 3.3 lbs (1.5 kg)
Connector 8 × 4.3-10 female
Mounting Pole 2 to 5 in (5 to 12 cm)
* Weight excludes mounting and RET

 

 

Bottom View  
   PI BSA33RU3A BOTTOM LABEL

 

Connector Spacing  
   PI BSA33RU3AA Connector Spacing
Element and RET Configuration  
   PI BSA33RU3AA RET Config Diagram

Typical Antenna Patterns

  For detailed information on additional antenna patterns, contact customer support at
Left Right PI BSA33RU3AA AP 1900 AZ PI BSA33RU3AA AP 1900 EL5
  1900 MHz Azimuth 1900 MHz Elevation 5°
Left Right PI BSA33RU3AA AP 2120 AZ PI BSA33RU3AA AP 2120 EL5
  2120 MHz Azimuth 2120 MHz Elevation 5°
Left Right PI BSA33RU3AA AP 2310 AZ PI BSA33RU3AA AP 2310 EL5
  2310 MHz Azimuth 2310 MHz Elevation 5°
Model BSA-RET200   Remote Electrical Tilt System (RET)
MBK-10   MBK-10
CBK-AG-RRU-001   Bi-Sector antenna with 2 RET to RRU AISG cable kit
CBK-RA-AG-RRU-001   Bi-Sector antenna with 2 RET to RRU AISG right angle cable kit 
SCU-AISG-P   Portable AISG 2.0 Site Control Unit

Software/Firmware

pdficon large Firmware Upgrade Instructions
 softwareicon Current Firmware

Parts & Accessories

BSA33R-U3AA-K Three foot (0.9 m), eight port, Bi-SectorTM antenna with left and right azimuth beams covering 1695-2400 MHz. with 4.3-10 female connectors, 2 factor installed RET actuators and MBK-10 mounting bracket
MBK-10 Mounting bracket kit (top and bottom) with 0° to 10° mechanical tilt adjustment
BSA-RET200 Remote electrical tilt actuator
CBK-AG-RRU-001 Two RET antenna to RRU AISG cable kit
CBK-RA-AG-RRU-001 Two RET antenna to RRU AISG right angle cable kit

Standards & Compliance

Safety EN 60950-1, UL 60950-1
Emission EN 55022
Immunity EN 55024
Environmental IEC 60068-2-1, IEC 60068-2-2, IEC 60068-2-5, IEC 60068-2-6, IEC-60068-2-11, IEC 60068-2-14, IEC 60068-2-18, IEC 60068-2-27, IEC 60068-2-29, IEC 60068-02-30, IEC 60068-2-52, IEC 60068-2-64, GR-63-CORE 4.3.1, EN 60529, IP 24

Certifications

Antenna Interface Standards Group (AISG), Federal Communication Commission (FCC) Part 15 Class B, CE, CSA US, ISO 9001:2008
 
ISO9001Logo RoHS logo AISGLogo 3GPPLogo
  Footer
              
     
     
       
 

News

CCILogoType

89 Leuning Street

South Hackensack, NJ 07606

+1 (201) 342-3338

+1 (201) 342-3339 fax