Bi-Sector Array Antennas

CCI Portal Login

CCI Customer Portal

CCI Register

In the Americas
   
 
 
 
Sales  
 
 
+1 (201) 342-3338 phone  
+1 (201)-342-3339 fax  
 
89 Leuning Street  
South Hackensack, NJ 07606  
USA  
 
Customer Service  
 
 
+1 (201) 342-3338 phone  
+1 (201)-342-3339 fax  
 
89 Leuning Street  
South Hackensack, NJ 07606  
USA  
 
Technical Support  
 
 
+1 (201) 342-3338 phone  
+1 (201)-342-3339 fax  
 
89 Leuning Street  
South Hackensack, NJ 07606  
USA  
 
 
      Hybrid Bi-SectorTM Array HBSA33R-KU6A
                
       
       
         
  PI HBSA33RKU6AA FRONT ISO PI HBSA33RKU6AA REAR ISO  
  • Six foot (1.9 m), multiband, Ten port Hybrid Bi-Sector Antenna. Deploying a high performing 65° azimuth beamwidth covering 698-960 MHz and a pair of CCI’s Patented Asymmetrical 33° Shaped Beams covering 1695-2400 MHz frequencies
  • Eight wide high band ports covering 1695-2400 MHz and two wide low band ports covering 698-960 MHz in a single antenna
  • Narrow Enclosure, 13.4” (340 mm) width. Narrowest Enclosure in the Industry for this type of Antenna
  • Full Spectrum Compliance for WCS and AWS-3 Frequencies and upcoming Band 14 Operations
  • LTE Optimized Asymmetric Shaped Beams for improved LTE data throughput by minimizing beam crossover, providing for an efficient use of valuable radio capacity and frequency spectrum
  • LTE Optimized FBR, SPR and Boresight/Sector XPD Performance, essential for today’s LTE Data Networks
  • Exceeds minimum PIM performance requirements
  • Equipped with new 4.3-10 connector, which is 40% smaller than traditional 7/16 DIN connector
  • Equipped with Three Field Replaceable, integrated AISG 2.0 compliant Remote Electrical Tilt (RET)

Overview

 

This version of the CCI Hybrid Bi-Sector Multiband Array is a ten port antenna, with eight wide high band ports covering 1695-2400 MHz and two wide low band ports covering 698-960 MHz. The CCI Hybrid Bi-Sector array uses a pair of CCI’s Patented Asymmetric 33° Shaped Beams in the High Band frequencies and a high performance 65° azimuth beamwidth in the low band frequencies. The CCI Hybrid Bi-Sector Array thus provides the capability to deploy Dual (over split beams) 4×4 Multiple-input Multiple-output (MIMO) in the high band and Single 2x2 Multiple-input Multiple-output in the low band. The CCI Hybrid Bi-Sector Array utilizes three RET controllers, with a separate RET control for the Low Band ports and a separate RET control in the High Band for each LEFT and RIGHT pair of CCI’s Patented Asymmetric 33° Shaped Beams.
The CCI Hybrid Bi-Sector Multiband Array, allow operators to reduce antenna count and replace existing 65° networks, while increasing cell site capacity and LTE data throughput by minimizing overlap between CCI’s Patented Asymmetric 33° Shaped Beams. This design approach lowers interference between sectors. All of this is achieved through a single panel array, producing significant CAPEX and OPEX cost savings for the operator.
CCI antennas are designed and produced to ISO 9001:2008 certification standards for reliability and quality in our state-of-the-art manufacturing facilities.

Applications

 
  • Dual (over split beams) 4x4 MIMO on High Band and 2x2 MIMO
    on Low Band
  • Ready for Network Standardization on 4.3-10 connectors
  • Ideal Antenna Solution for structurally constrained sites, where data throughput, capacity and limited spectrum is a concern
  • With CCI’s Hybrid Bi-Sector Antenna, wireless operators can connect multiple platforms to a single antenna, reducing tower load, lease expense, deployment time and installation cost

Electrical

Ports 2 × Low Band Ports for 698-960 MHz
Frequency Range 698-806 MHz 824-896 MHz 880-960 MHz
Gain1 14.5 dBi 14.6 dBi 14.6 dBi
Gain (Average)2 14.1 dBi 14.3 dBi 14.1 dBi
Azimuth Beamwidth (-3dB) 65° 65° 61°
Elevation Beamwidth (-3dB) 12.7° 11.0° 10.3°
Electrical Downtilt 0° to 10° 0° to 10° 0° to 10°
Elevation Sidelobes (1st Upper) < -18 dB < -18 dB < -18 dB
Front-to-Back Ratio @180° > 29 dB > 30 dB > 35 dB
Front-to-Back Ratio over ± 20° > 29 dB > 30 dB > 35 dB
Cross-Polar Discrimination (at Peak) > 24 dB > 25 dB > 25 dB
Cross-Polar Port-to-Port Isolation > 25 dB > 25 dB > 25 dB
Voltage Standing Wave Ratio(VSWR) < 1.5:1 < 1.5:1 < 1.5:1
Passive Intermodulation (2×20W) ≤ -150 dBc ≤ -150 dBc ≤ -150 dBc
Input Power Continuous Wave (CW) 500 watts 500 watts 500 watts
Polarization Dual Pol 45° Dual Pol 45° Dual Pol 45°
Input Impedance 50 ohms 50 ohms 50 ohms
Lightning Protection DC Ground DC Ground DC Ground
1Peak gain across sub-bands.
2Electrical specifications follow document "Recommendation on Base Station Antenna Standards" (BASTA) V9.6.

 

Ports 8 × High Band Ports for 1695-2400 MHz
Frequency Range 1695-1880 MHz 1850-1990 MHz 1920-2180 MHz 2300-2400 MHz
Gain1 17.5 dBi 17.9 dBi 18.3 dBi 18.7 dBi
Gain (Average)2 16.6 dBi 17.2 dBi 17.5 dBi 18.1 dBi
Azimuth Beamwidth (-3dB) 36° 34° 32° 29°
Elevation Beamwidth (-3dB) 9.7° 8.9° 8.5° 7.5°
Electrical Downtilt 0° to 10° 0° to 10° 0° to 10° 0° to 10°
Elevation Sidelobes (1st Upper) < -17 dB < -16 dB < -17 dB < -18 dB
Front-to-Back Ratio @180° > 35 dB > 35 dB > 35 dB > 35 dB
Front-to-Back Ratio over ± 20° > 30 dB > 30 dB > 30 dB > 30 dB
Cross-Polar Discrimination (at Peak) > 25 dB > 25 dB > 25 dB > 25 dB
Cross-Polar Port-to-Port Isolation > 25 dB > 25 dB > 25 dB > 25 dB
Voltage Standing Wave Ratio(VSWR) < 1.5:1 < 1.5:1 < 1.5:1 < 1.5:1
Passive Intermodulation (2×20W) ≤ -150 dBc ≤ -150 dBc ≤ -150 dBc ≤ -150 dBc
Input Power Continuous Wave (CW) 300 watts 300 watts 300 watts 300 watts
Polarization Dual Pol 45° Dual Pol 45° Dual Pol 45° Dual Pol 45°
Input Impedance 50 ohms 50 ohms 50 ohms 50 ohms
Lightning Protection DC Ground DC Ground DC Ground DC Ground
1Peak gain across sub-bands.
2Electrical specifications follow document "Recommendation on Base Station Antenna Standards" (BASTA) V9.6.

Mechanical

Dimensions (L×W×D) 76.0×13.4×8.5 in (1932×340×216 mm)
Survival Wind Speed > 150 mph (> 241 kph)
Front Wind Load 243 lbs (1080 N) @ 100 mph (161 kph)
Side Wind Load 168 lbs (749 N) @ 100 mph (161 kph)
Equivalent Flat Plate Area 9.5 ft2 (0.9 m2)
Weight* 50.5 lbs (22.9 kg)
RET System Weight 5.0 lbs (2.3 kg)
Connector 10 × 4.3-10 female
Mounting Pole 2 to 5 in (5 to 12 cm)
* Weight excludes mounting and RET
Bottom View  
   PI HBSA33RKU6AA BOT LABEL
Connector Spacing  
  PI HBSA33RKU6AA connector spacing
RET to Array Configuration  
  PI HBSA33RKU6A RET Element Config

Typical Antenna Patterns

Connector Spacing  
  For detailed information on additional antenna patterns, contact customer support at
Azumuth elevation HBSA33RKU6AA AP 722 AZEL5 HBSA33RKU6AA AP 850 AZEL5
  722 MHz Azimuth with Elevation 5° 850 MHz Azimuth with Elevation 5°
Left Right Elevation HBSA33RKU6AA AP 1920 AZEL5 HBSA33RKU6AA AP 2110 AZEL5
  1920 MHz Azimuth with Elevation 5° 2110 MHz Azimuth with Elevation 5°
MBK-01   MBK-01 Mounting Kit
BSA-RET200   Remote Electrical Tilt System (RET)
HPA-CBK-AG-RRU   TriBand antenna with 3 RET to RRU AISG cable kit
HPA-CBK-RA-AG-RRU   TriBand antenna with 3 RET to RRU AISG right angle cable kit 
SCU-AISG2-P   Portable AISG 2.0 Site Control Unit

Software/Firmware

pdficon large HPA-Firmware Upgrade Instructions
 softwareicon Current Firmware

Parts & Accessories


HBSA33R-KU6AA-K Six foot (1.9 m) Hybrid Bi-Sector Antenna Array with 4.3-10 female connector, 3 factory installed external BSA-RET200 RET actuators (Type 1 External) and MBK-01 mounting brackets
MBK-01 Mounting bracket kit (top and bottom) with 0° to 10° mechanical tilt adjustment
BSA-RET200 Type 1 remote electrical tilt actuator
HPA-CBK-AG-RRU Hybrid Bi-Sector antenna to RRU AISG cable kit
HPA-CBK-RA-AG-RRU Hybrid Bi-Sector antenna to RRU AISG right angle cable kit

Standards & Compliance

Safety EN 60950-1, UL 60950-1
Emission EN 55022
Immunity EN 55024
Environmental IEC 60068-2-1, IEC 60068-2-2, IEC 60068-2-5, IEC 60068-2-6, IEC-60068-2-11, IEC 60068-2-14, IEC 60068-2-18, IEC 60068-2-27, IEC 60068-2-29, IEC 60068-02-30, IEC 60068-2-52, IEC 60068-2-64, GR-63-CORE 4.3.1, EN 60529, IP 24

Certifications

Antenna Interface Standards Group (AISG), Federal Communication Commission (FCC) Part 15 Class B, CE, CSA US, ISO 9001:2008
 
ISO9001Logo RoHS logo AISGLogo 3GPPLogo
  Footer
              
     
     
       
 

News

CCILogoType

89 Leuning Street

South Hackensack, NJ 07606

+1 (201) 342-3338

+1 (201) 342-3339 fax