Bi-Sector Array Antennas

CCI Portal Login

CCI Customer Portal

CCI Register

In the Americas
   
 
 
 
Sales  
 
 
+1 (201) 342-3338 phone  
+1 (201)-342-3339 fax  
 
89 Leuning Street  
South Hackensack, NJ 07606  
USA  
 
Customer Service  
 
 
+1 (201) 342-3338 phone  
+1 (201)-342-3339 fax  
 
89 Leuning Street  
South Hackensack, NJ 07606  
USA  
 
Technical Support  
 
 
+1 (201) 342-3338 phone  
+1 (201)-342-3339 fax  
 
89 Leuning Street  
South Hackensack, NJ 07606  
USA  
 
 
      Multi-Band Bi-SectorTM Array BSA-M65R-DU-H6
                
       
       
         
  PI BSAM65RDUH6 front iso PI BSAM65RDUH6 rear iso  
  • Patented twin asymmetric beam 33° Bi-Sector array phased arrays over a frequency range of (790-960 MHz) and (1710-2360 MHz), optimized to match existing cloverleaf (65°) deployments.
  • 4 low band and 4 high band ports.
  • Single panel design supporting 2 beams.
  • Optimized beam shape for maximum LTE data throughput.Independent low-band and high-band remote electrical tilt for each beam provides unmatched optimization flexibility.
  • 3GPP/AISG 2.0 compliant.
  • Daisy chaining capability.
  • Software upgradeable.
  • Rugged, weather resistant and highly reliable internal design.

Overview

 

The CCI Multi-Band Bi-Sector Antenna is an LTE optimized phased array that provides a total of four low band ports covering the 800 MHz thru 900 MHz bands and four high band ports covering the DCS 1800 and UMTS 2100 bands in a single, compact enclosure. Our patented bi-sector technology enables the creation of two asymmetric 33° beams, each containing two low band and two high band ports. The antenna is capable of 2x2 MIMO in both low and high bands. The beam shapes have been optimized for minimum overlap and crossover in order to minimize interference across sectors and lower soft handover losses. As such, the antenna array enables maximized data throughput for EVDO, UMTS and LTE networks.

The remote electrical tilt (RET) Series Multi-Band Bi-Sector Antenna enables operators to remotely control the electrical down-tilt of the antenna in the field with sealed AISG compliant RET actuators. The CCI RET system is designed to meet the reliability, flexibility and efficiency requirements in a wide range of environments. The RET actuators are fully AISG compliant, software upgradeable, daisy chaining capable and fully weather resistant. The remote electrical capability allows independent adjustment of the low band ports and high band ports of each sub-beam for easier optimization. This antenna is also available as a variable electrical tilt (VET) model.

The single panel design of the antenna array offers the opportunity to reduce antenna count and directly replaces the footprint of an existing 65° antenna. The new coverage that matches the existing footprint minimizes the need for optimization and adjacent site changes, and allows for significant CAPEX and OPEX cost savings.

CCI antennas are designed and produced to ISO 9001:2008 certification standards for reliability and quality in our state-of-the-art manufacturing facilities.

Applications

 
  • Upgrade of data-throughput or capacity constrained sites.
  • Spectrum limited markets.
  • Deferral of new site builds or carrier adds.

Electrical

Ports 4 × Low Band Ports for 790-960 MHz 4 × High Band Ports for 1710-2360 MHz
Frequency Range 790-862 MHz 880-960 MHz 1710-1880 MHz 1920-2170 MHz 2300-2360 MHz
Gain 17.1 dBi 17.5 dBi 17.5 dBi 18.4 dBi 18.5 dBi
Azimuth Beamwidth (-3dB) 32° 30° 32° 29° 25°
Elevation Beamwidth (-3dB) 10.8° 9.7° 6.9° 6.0° 5.5°
Electrical Downtilt 2° to 12° 2° to 12° 0° to 9° 0° to 9° 0° to 9°
Elevation Sidelobes (1st Upper) < -18 dB < -18 dB < -18 dB < -18 dB < -18 dB
Front-to-Back Ratio @180° > 30 dB > 30 dB > 30 dB > 30 dB > 30 dB
Front-to-Back Ratio over ± 20° > 30 dB > 30 dB > 30 dB > 30 dB > 28 dB
Cross-Polar Port-to-Port Isolation > 25 dB > 25 dB > 25 dB > 25 dB > 25 dB
Voltage Standing Wave Ratio(VSWR) < 1.5:1 < 1.5:1 < 1.5:1 < 1.5:1 < 1.5:1
Passive Intermodulation (2×20W) ≤ -150 dBc ≤ -150 dBc ≤ -150 dBc ≤ -150 dBc ≤ -150 dBc
Input Power Continuous Wave (CW) 500 watts 500 watts 300 watts 300 watts 300 watts
Polarization Dual Linear45° Dual Linear 45° Dual Linear 45° Dual Linear 45° Dual Linear 45°
Input Impedance 50 ohms 50 ohms 50 ohms 50 ohms 50 ohms
Lightning Protection DC Ground DC Ground DC Ground DC Ground DC Ground

Mechanical

Dimensions (L×W×D) 72.0×28.5×9.7 in (1828×723×245 mm)
Survival Wind Speed > 150 mph (> 240 kph)
Front Wind Load 438 lbs (1947N) @ 100 mph (161 kph)
Side Wind Load 175 lbs (778N) @ 100 mph (161 kph)
Equivalent Flat Plate Area 17.1 ft2 (1.6 m2)
Weight * 96.3 lbs (43.7 kg)
RET System Weight 6.6 lbs (3.0 kg)
Connector 8 × 7-16 DIN female long neck
Mounting Pole 2 to 5 in (5 to 12 cm)
* Weight excludes mounting and RET
Bottom View   RET Connection Diagram
   PI BSAM65RDUH6 Bottom lable PI BSAM65RDUH6 ret
Connector Spacing  
  PI BSAM65RDUH6 Connector Spacing

Typical Antenna Patterns

  For detailed information on additional antenna patterns, contact customer support at
  BSAM65RDUH6 AP 849 AZ BSAM65RDUH6 AP 849 EL7
  849 MHz Azimuth  849 MHz Elevation 7°
  BSAM65RDUH6 AP 915 AZ BSAM65RDUH6 AP 915 EL7
   915 MHz Azimuth 915 MHz Elevation 7°
  BSAM65RDUH6 AP 1910 AZ BSAM65RDUH6 AP 1910 EL5
  1910 MHz Azimuth 1910 MHz Elevation 5°
Model BSA-RET200   Remote Electrical Tilt System (RET)

Software/Firmware

pdficon large Firmware Upgrade Instructions
 softwareicon Current Firmware

Parts & Accessories

BSA-M65R-DU-H6 6 Foot (1.8 m) Bi-Sector Array, Multi-Band Antenna with 4 factory installed RET Actuators
BSA-M65V-DU-H6 6 Foot (1.8 m) Bi-Sector Array, Multi-Band Antenna, Variable Electrical Tilt with 4 factory installed knobs
BSA-M65R-DU-H6-K Complete Kit with Antenna, Factory Installed Actuators (4) and MBK-01 Mounting Bracket
BSA-M65V-DU-H6-K Complete Kit with Antenna, manual Variable Electrical Tilt (4) and MBK-01 Mounting Bracket
MBK-01 Mounting bracket kit (top and bottom) with 0° to 10° mechanical tilt adjustment
BSA-RET200 Remote electrical tilt actuator
OPA-CBK-AG-RRU 4 RET antenna to RRU AISG cable kit
OPA-CBK-RA-AG-RRU 4 RET  antenna to RRU AISG right angle cable kit

Standards & Compliance

Safety EN 60950-1, UL 60950-1
Emission EN 55022
Immunity EN 55024
Environmental IEC 60068-2-1, IEC 60068-2-2, IEC 60068-2-5, IEC 60068-2-6, IEC-60068-2-11, IEC 60068-2-14, IEC 60068-2-18, IEC 60068-2-27, IEC 60068-2-29, IEC 60068-02-30, IEC 60068-2-52, IEC 60068-2-64, GR-63-CORE 4.3.1, EN 60529, IP 24

Certifications

Antenna Interface Standards Group (AISG), Federal Communication Commission (FCC) Part 15 Class B, CE, CSA US, ISO 9001:2008
 
ISO9001Logo RoHS logo AISGLogo 3GPPLogo
  Footer
              
     
     
       
 

News

CCILogoType

89 Leuning Street

South Hackensack, NJ 07606

+1 (201) 342-3338

+1 (201) 342-3339 fax