Bi-Sector Array Antennas

CCI Portal Login

CCI Customer Portal

CCI Register

In the Americas
+1 (201) 342-3338 phone  
+1 (201)-342-3339 fax  
89 Leuning Street  
South Hackensack, NJ 07606  
Customer Service  
+1 (201) 342-3338 phone  
+1 (201)-342-3339 fax  
89 Leuning Street  
South Hackensack, NJ 07606  
Technical Support  
+1 (201) 342-3338 phone  
+1 (201)-342-3339 fax  
89 Leuning Street  
South Hackensack, NJ 07606  
      Low-band Bi-Sector™ Array BSA-S65R-D-H6
  PI BSAS65RDH6 front iso 20150729 PI BSAS65RDH6 rear iso 20150729  
  • Patented twin asymmetric beam 33° Bi-Sector array phased arrays over a frequency range of (790-960 MHz), optimized to match existing cloverleaf (65°) deployments.
  • 4 low band ports
  • Single panel design supporting 2 beams
  • Optimized beam shape for maximum LTE data throughput
  • 3GPP/AISG 2.0 compliant
  • Multi band applications – 800 MHz, 900 MHz
  • Provides independent remote control of electrical downtilt for each beam for ease of optimization



The CCI Low Band Bi-Sector Antenna is an LTE optimized phased array that provides a total of four low band ports covering the 800 MHz thru 900 MHz bands. Our patented bi-sector technology enables the creation of two asymmetric 33° beams each containing two low band ports. The antenna is capable of 2x2 MIMO. The beam shapes have been optimized for minimum overlap and crossover in order to minimize interference across sectors and lower soft handover losses. As such, the antenna array enables maximized data throughput for EVDO, UMTS and LTE networks. 

This antenna is available as either a remote electrical tilt (RET) or a variable electrical tilt (VET) model. The RET Low Band Bi-Sector Antenna enables operators to remotely control the electrical down-tilt of the antenna in the field with sealed AISG compliant RET actuators. The CCI RET system is designed to meet the reliability, flexibility and efficiency requirements in a wide range of environments. The RET actuators are fully AISG compliant, software upgradeable, daisy chaining capable and fully weather resistant. The remote electrical capability allows independent adjustment of the low band ports each beam for easier optimization.

The single panel design of the antenna array offers the opportunity to reduce antenna count and directly replaces the footprint of an existing 65° antenna. The new coverage that matches the existing footprint minimizes the need for optimization and adjacent site changes, and allows for significant CAPEX and OPEX cost savings.

CCI antennas are designed and produced to ISO 9001:2008 certification standards for reliability and quality in our state-of-the-art manufacturing facilities.


  • Upgrade of data-throughput or capacity constrained sites
  • Spectrum limited markets
  • Deferral of new site builds or carrier adds
  • Spectrum clearing and re-farming


Ports 4 × Low Band Ports for 790-960 MHz
Frequency Range 790-862 MHz 880-960 MHz
Gain 17.1 dBi 17.5 dBi
Azimuth Beamwidth (-3dB) 32° 30°
Elevation Beamwidth (-3dB) 10.8° 9.7°
Electrical Downtilt 2° to 12° 2° to 12°
Elevation Sidelobes (1st Upper) < -18 dB < -18 dB
Front-to-Back Ratio @180° > 30 dB > 30 dB
Front-to-Back Ratio over ± 20° > 30 dB > 30 dB
Cross-Polar Port-to-Port Isolation > 25 dB > 25 dB
Voltage Standing Wave Ratio (VSWR) < 1.5:1 < 1.5:1
Passive Intermodulation (2×20W) ≤ -150 dBc ≤ -150 dBc
Input Power Continuous Wave (CW) 500 watts 300 watts
Polarization Dual Linear 45° Dual Linear 45°
Input Impedance 50 ohms 50 ohms
Lightning Protection DC Ground DC Ground


Dimensions (L×W×D) 72.0×28.5×9.7 in (1828×723×245 mm)
Survival Wind Speed > 150 mph (> 241 kph)
Front Wind Load 438 lbs (1947 N) @ 100 mph (161 kph)
Side Wind Load 175 lbs (778 N) @ 100 mph (161 kph)
Equivalent Flat Plate Area 17.1 ft2 (1.6 m2)
Weight * 81.4 lbs (36.9 kg)
RET System Weight 3.3 lbs (1.5 kg)
Connector 4 × 7-16 DIN female long neck
Mounting Pole 2 to 5 in (5 to 12 cm)
* Weight excludes mounting and RET
Bottom View   RET Connection Diagram
  PI BSAS65RDH4H6 bottom with labels 20151123 PI BSAS65RDH6 RETDIAGRAM
Connector Spacing  

Typical Antenna Patterns

  For detailed information on additional antenna patterns, contact customer support at
  BSAS65RDH6 AP 849 AZ BSAS65RDH6 AP 849 EL7
  849 MHz Azimuth  849 MHz Elevation 7°
  BSAS65RDH6 AP 915 AZ BSAS65RDH6 AP 915 EL7
  915 MHz Azimuth  915 MHz Elevation 7°
Model BSA-RET200   Remote Electrical Tilt System (RET)


pdficon large Firmware Upgrade Instructions
 softwareicon Current Firmware

Parts & Accessories

BSA-S65R-D-H6 6 foot (1.8 M) Bi-Sector array antenna and 2 factory installed BSA-RET200 RET actuators
BSA-S65V-D-H6 6 foot (1.8 M) Bi-Sector array antenna and 2 factory installed manual knob
BSA-S65R-D-H6-K Antenna kit with 2 factory installed RET actuators  and MBK-01 mounting bracket
BSA-S65V-D-H6-K Antenna kit with2 factory installed manual knob and MBK-01 mounting bracket
MBK-01 Mounting bracket kit (top and bottom) with 0° to 10° mechanical tilt adjustment
BSA-RET200 Remote electrical tilt actuator
QPA-CBK-AG-RRU QuadPort antenna to RRU AISG cable kit
QPA-CBK-RA-AG-RRU QuadPort antenna to RRU AISG right angle cable kit

Standards & Compliance

Safety EN 60950-1, UL 60950-1
Emission EN 55022
Immunity EN 55024
Environmental IEC 60068-2-1, IEC 60068-2-2, IEC 60068-2-5, IEC 60068-2-6, IEC-60068-2-11, IEC 60068-2-14, IEC 60068-2-18, IEC 60068-2-27, IEC 60068-2-29, IEC 60068-02-30, IEC 60068-2-52, IEC 60068-2-64, GR-63-CORE 4.3.1, EN 60529, IP 24


Antenna Interface Standards Group (AISG), Federal Communication Commission (FCC) Part 15 Class B, CE, CSA US, ISO 9001:2008
ISO9001Logo RoHS logo AISGLogo 3GPPLogo


89 Leuning Street

South Hackensack, NJ 07606

+1 (201) 342-3338

+1 (201) 342-3339 fax