Bi-Sector Array Antennas

CCI Portal Login

CCI Customer Portal

In the Americas
+1 (201) 342-3338 phone  
+1 (201)-342-3339 fax  
89 Leuning Street  
South Hackensack, NJ 07606  
Customer Service  
+1 (201) 342-3338 phone  
+1 (201)-342-3339 fax  
89 Leuning Street  
South Hackensack, NJ 07606  
Technical Support  
+1 (201) 342-3338 phone  
+1 (201)-342-3339 fax  
89 Leuning Street  
South Hackensack, NJ 07606  
      Wideband Bi-SectorTM Array BSA-W65-20R210-02
To Be Discontinued
  PI BSAW6520R21002 front iso 20150716 PI BSAW6520R21002 rear iso 20150716  
  • Four and a half foot (1.4m), four port, dual beam antenna with patented asymmetrical beam shapes optimized for LTE
  • Two wideband 33° beams to match existing 65° patterns, covering 1710-2170 MHz
  • One pair of +45° and –45° cross-polarized ports for each beam
  • Slim and low weight single panel design supporting two beams in a single antenna
  • Field replaceable, integrated AISG 2.0 compliant Remote Electrical Tilt (RET) system with independent tilt control for each beam
  • Dramatic increase in site capacity through higher order sectorization which offsets the need to build new sites
  • Boosts data throughput by minimizing interference and optimizing coverage
  • Sharp elevation beamwidth aides in network planning
  • Optimal elevation sidelobe performance
  • Exceeds minimum PIM performance requirements



The CCI wideband Bi-SectorTM array is a dual beam antenna with full AWS and PCS band coverage. With two pairs of wideband ports each covering 1710-2170 MHz and 1850-1990 MHz, this four and a half foot (1.4 m) CCI Bi-Sector provides the capability to deploy two beams (sectors) in a single antenna. This Remote Electrical Tilt (RET) antenna allows separate tilt control for each beam individually, enabling maximum flexibility in network deployment.

CCI's unique patented bi-sector technology provides optimized overlap between the pairs of asymmetric beams, lowers soft handover losses in LTE, UMTS/HSPA+ and CDMA/EVDO systems, while minimizing interference between sectors. Fast roll-off of each of the outer beams and high front-to-back ratios ensure reduced interference. This patented approach enhances data transfer rates within LTE, UMTS and EVDO network sectors and addresses “hotspots” in mobile wireless operator networks.

The single panel design of the Bi-Sector Array offers the opportunity to reduce antenna count and directly replaces an existing 65° antenna without mount changes and avoids costly leasing and zoning changes. The enhanced coverage matches the existing sector footprint and minimizes the need for optimization and adjacent site changes, providing operators with significant CAPEX and OPEX cost savings.

CCI antennas are designed and produced to ISO 9001:2008 certification standards for reliability and quality in our state-of-the-art manufacturing facilities.


  • Delivers increased capacity and data-throughput for sites that are performance or capacity constrained
  • Provides a higher level of spectrum reuse making it an ideal solution for spectrum limited markets
  • Increase capacity without the need for new site builds or carrier adds and without using valuable spectrum resources
  • Efficient use of spectrum makes it ideally suited for spectrum clearing and refarming


Ports 4 × High Band Ports for 1710-2170 MHz
Frequency Range 1710-1880 MHz 1850-1990 MHz 1920-2170 MHz
Gain 18.7 dBi 19.2 dBi 19.8 dBi
Azimuth Beamwidth (-3dB) 31° 29° 28°
Elevation Beamwidth (-3dB) 8.0° 7.2° 6.5°
Electrical Downtilt 2° to 10° 2° to 10° 2° to 10°
Elevation Sidelobes (1st Upper) < -18 dB < -18 dB < -18 dB
Front-to-Back Ratio @180° > 30 dB > 30 dB > 30 dB
Cross-Polar Port-to-Port Isolation > 30 dB > 30 dB > 30 dB
Voltage Standing Wave Ratio(VSWR) < 1.4:1 < 1.4:1 < 1.4:1
Passive Intermodulation (2×20W) ≤ -150 dBc ≤ -150 dBc ≤ -150 dBc
Input Power Continuous Wave (CW) 300 watts 300 watts 300 watts
Polarization ±45° Slant ±45° Slant ±45° Slant
Input Impedance 50 ohms 50 ohms 50 ohms
Lightning Protection DC Ground DC Ground DC Ground


Dimensions (L×W×D) 55.9×15.6×6.7 in (1421×397×171 mm)
Survival Wind Speed > 120 mph (> 193 kph)
Front Wind Load 194 lbs (863 N) @ 100 mph (161 kph)
Side Wind Load 97 lbs (430 N) @ 100 mph (161 kph)
Equivalent Flat Plate Area 7.6 ft2 (0.7 m2)
Weight * 39.5 lbs (17.9 kg)
RET System Weight 3.3 lbs (1.5 kg)
Connector 4 × 7-16 DIN female
Mounting Pole 2 to 5 in (5 to 12 cm)
* Weight excludes mounting and RET
Bottom View   RET
  PI BSAW6520R21002 bottom 20150716 PI BSAW6520R21002 ret
Connector Spacing  

Typical Antenna Patterns

  For detailed information on additional antenna patterns, contact customer support at
  BSAW6520R21002 AP AZ1920 BSAW6520R21002 AP AZ1920 EL2
  1920 MHz Azimuth 1920 MHz Azimuth Elevation 2°
  BSAW6520R21002 AP AZ1920 EL6 BSAW6520R21002 AP AZ1920 EL10
  1920 MHz Azimuth Elevation 6° 1920 MHz Azimuth Elevation 10°
Model BSA-RET200   Remote Electrical Tilt System (RET)


pdficon large HPA-Firmware Upgrade Instructions
 softwareicon Current Firmware

Parts & Accessories

BSA-W65-20R210-02 Five foot Bi-Sector array, Wideband (1800, 1900, 2110 MHz) and 2 factory installed BSA-RET200 RET actuators
BSA-W65-20R210-02-K Antenna kit with 2 factory installed RET actuators and MBK-02 mounting bracket
MBK-02 Mounting bracket kit (top and bottom) with 0° to 10° mechanical tilt adjustment
BSA-RET200 Remote electrical tilt actuator
QPA-CBK-AG-RRU Quad Port antenna to RRU AISG cable kit
QPA-CBK-RA-AG-RRU Quad Port antenna to RRU AISG right angle cable kit

Standards & Compliance

Safety EN 60950-1, UL 60950-1
Emission EN 55022
Immunity EN 55024
Environmental IEC 60068-2-1, IEC 60068-2-2, IEC 60068-2-5, IEC 60068-2-6, IEC-60068-2-11, IEC 60068-2-14, IEC 60068-2-18, IEC 60068-2-27, IEC 60068-2-29, IEC 60068-02-30, IEC 60068-2-52, IEC 60068-2-64, GR-63-CORE 4.3.1, EN 60529, IP 24


Antenna Interface Standards Group (AISG), Federal Communication Commission (FCC) Part 15 Class B, CE, CSA US, ISO 9001:2008
ISO9001Logo RoHS logo AISGLogo 3GPPLogo


89 Leuning Street

South Hackensack, NJ 07606

+1 (201) 342-3338

+1 (201) 342-3339 fax