Bi-Sector Array Antennas

CCI Portal Login

CCI Customer Portal

CCI Register

In the Americas
   
 
 
 
Sales  
 
 
+1 (201) 342-3338 phone  
+1 (201)-342-3339 fax  
 
89 Leuning Street  
South Hackensack, NJ 07606  
USA  
 
Customer Service  
 
 
+1 (201) 342-3338 phone  
+1 (201)-342-3339 fax  
 
89 Leuning Street  
South Hackensack, NJ 07606  
USA  
 
Technical Support  
 
 
+1 (201) 342-3338 phone  
+1 (201)-342-3339 fax  
 
89 Leuning Street  
South Hackensack, NJ 07606  
USA  
 
 
      Multi-band Bi-SectorTM Array BSA-D65-19R010-02
To Be Discontinued
                
       
       
         
  PI BSAD6519R01002 front iso 20150707 PI BSAD6519R01002 rear iso 20150707  
  • Six foot (1.8 m), eight port, multi-band Bi-SectorTM  array with patented asymmetrical beam shapes optimized for LTE
  • Two low band and two high band 33° beams to match existing 65° patterns, covering 790-960 MHz and 1710-2170 MHz
  • One pair of +45° and –45° cross-polarized ports for each beam
  • Slim and low weight single panel design supporting two beams in a single antenna
  • Field replaceable, integrated AISG 2.0 compliant Remote Electrical Tilt(RET) system with independent tilt control for each beam
  • Dramatic increase in site capacity through higher order sectorization which offsets the need to build new sites
  • Boosts data throughput by minimizing interference and optimizing coverage
  • Sharp elevation beamwidth aides in network planning
  • Optimal elevation sidelobe performance
  • Exceeds minimum PIM performance requirements

Overview

 

The CCI multi-band Bi-SectorTM array is a dual beam antenna with full LTE 800, Cellular 850, LTE 900, DCS 1800 and UMTS 2100 band coverage. With two pairs of high band ports covering 1710-2170 MHz and two pairs of low band ports covering 790-960 MHz, this six foot (1.8 m) CCI Bi-Sector provides the capability to deploy two high band beams (sectors) and two low band beams (sectors) in a single antenna. This Remote Electrical Tilt (RET) antenna allows separate tilt control for each beam individually, enabling maximum flexibility in network deployment.

CCI's unique patented bi-sector technology provides optimized overlap between the pairs of asymmetric beams, lowers soft handover losses in LTE, UMTS/HSPA+ and CDMA/EVDO systems, while minimizing interference between sectors. Fast roll-off of each of the outer beams and high front-to-back ratios ensure reduced interference. This patented approach enhances data transfer rates within LTE, UMTS and EVDO network sectors and addresses “hotspots” in mobile wireless operator networks.

The single panel design of the Bi-Sector Array offers the opportunity to reduce antenna count and directly replaces an existing 65° antenna without mount changes and avoids costly leasing and zoning changes. The enhanced coverage matches the existing sector footprint and minimizes the need for optimization and adjacent site changes, providing operators with significant CAPEX and OPEX cost savings.

CCI antennas are designed and produced to ISO 9001:2008 certification standards for reliability and quality in our state-of-the-art manufacturing facilities.

Applications

 
  • Delivers increased capacity and data-throughput for sites that are performance or capacity constrained
  • Provides a higher level of spectrum reuse making it an ideal solution for spectrum limited markets
  • Increase capacity without the need for new site builds or carrier adds and without using valuable spectrum resources
  • Efficient use of spectrum make it ideally suited for spectrum clearing and refarming

Electrical

Ports 4 × Low Band Ports for 790-960 MHz 4 × High Band Ports for 1710-2170 MHz 
Frequency Range 790-862 MHz 880-960 MHz 1710-1880 MHz 1920-2170 MHz
Gain 16.2 ± 1.0 dBi 16.8 ± 1.0 dBi 17.5 ± 1.0 dBi 18.1 ± 1.0 dBi
Azimuth Beamwidth (-3dB) 33.0° 31.0° 32.0° 31.0°
Elevation Beamwidth (-3dB) 11.2° ± 1° 10.3° ± 1° 6.1° ± 0.5° 5.3° ± 0.5°
Electrical Downtilt 0° to 10° 0° to 10° 0° to 8° 0° to 8°
Elevation Sidelobes (1st Upper) < -17 dB < -17 dB < -18 dB < -18 dB
Front-to-Back Ratio @180° > 30 dB > 25 dB > 33 dB > 35 dB
Cross-Polar Port-to-Port Isolation > 25 dB > 25 dB > 30 dB > 30 dB
Voltage Standing Wave Ratio(VSWR) < 1.5:1 < 1.5:1 < 1.5:1 < 1.5:1
Passive Intermodulation (2×20W) ≤ -150 dBc ≤ -150 dBc ≤ -150 dBc ≤ -150 dBc
Input Power Continuous Wave (CW) 250 watts 250 watts 250 watts 250 watts
Polarization Dual Linear 45° Dual Linear 45° Dual Linear 45° Dual Linear 45°
Input Impedance 50 ohms 50 ohms 50 ohms 50 ohms
Lightning Protection DC Ground DC Ground DC Ground DC Ground

Mechanical

Dimensions (L×W×D) 72.0×28.5×9.4 in (1828×723×240 mm)
Survival Wind Speed > 120 mph (> 193 kph)
Front Wind Load 438 lbs (1946 N) @ 100 mph (161 kph)
Side Wind Load 172 lbs (764 N) @ 100 mph (161 kph)
Equivalent Flat Plate Area 17.0 ft2 (1.6 m2)
Weight * 94.6 lbs (43.0 kg)
RET System Weight 6.6 lbs (3.0 kg)
Connector 8 × 7-16 DIN female long neck
Mounting Pole 2 to 5 in (5 to 12 cm)
* Weight excludes mounting and RET
Bottom View  
  PI BSAD6519R01002 bottom with labels 20150716
Connector Spacing  
  BSAD6519R01002 BVDim

Typical Antenna Patterns

  For detailed information on additional antenna patterns, contact customer support at
  BSAD6519R01002 AP AZ850 BSAD6519R01002 AP AZ1910 
  850 MHz Azimuth Elevation 5° 1910 MHz Azimuth Elevation 0°
Model BSA-RET200   Remote Electrical Tilt System (RET)

Software/Firmware

pdficon large HPA-Firmware Upgrade Instructions
 softwareicon Current Firmware

Parts & Accessories

BSA-D65-19R010-02 Six foot (1.8 m) Bi-Sector array, Dual-band (800, 850, 1900, 1710/2110 MHz) and 4 factory installed BSA-RET200 RET actuators
BSA-D65-19R010-02-K Antenna kit with 4 factory installed RET actuators and MBK-01 mounting bracket
MBK-01 Mounting bracket kit (top and bottom) with 0° to 10° mechanical tilt adjustment
BSA-RET200 Remote electrical tilt actuator
OPA-CBK-AG-RRU OctoPort antenna to RRU AISG cable kit
OPA-CBK-RA-AG-RRU OctoPort antenna to RRU AISG right angle cable kit

Standards & Compliance

Safety EN 60950-1, UL 60950-1
Emission EN 55022
Immunity EN 55024
Environmental IEC 60068-2-1, IEC 60068-2-2, IEC 60068-2-5, IEC 60068-2-6, IEC-60068-2-11, IEC 60068-2-14, IEC 60068-2-18, IEC 60068-2-27, IEC 60068-2-29, IEC 60068-02-30, IEC 60068-2-52, IEC 60068-2-64, GR-63-CORE 4.3.1, EN 60529, IP 24

Certifications

Antenna Interface Standards Group (AISG), Federal Communication Commission (FCC) Part 15 Class B, CE, CSA US, ISO 9001:2008
 
ISO9001Logo RoHS logo AISGLogo 3GPPLogo
  Footer
              
     
     
       
 

News

CCILogoType

89 Leuning Street

South Hackensack, NJ 07606

+1 (201) 342-3338

+1 (201) 342-3339 fax